A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
16711
1.INSTALL FAN SHROUD WITH COOLING FAN
Install the fan shroud with the 2 bolts.
88460
2.INSTALL COOLER CONDENSER ASSEMBLY
Attach the 2 guides to install the condenser assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>CONDENSER(for 3ZR-FE, 3ZR-FAE, 2AR-FE)>INSTALLATION
16712
3.INSTALL NO. 2 FAN SHROUD
Attach the 2 claws to install the No. 2 fan shroud.
Install the 2 bolts.
16535
4.INSTALL RADIATOR LOWER SUPPORT
Install the 2 radiator lower supports to the fan shroud.
16268L
5.INSTALL WATER BY-PASS PIPE
Install the water by-pass pipe to the radiator, and slide the hose clamp to secure it.
Attach the 3 clamps to connect the water by-pass pipe.
16572D
6.INSTALL NO. 2 RADIATOR HOSE
Install the No. 2 radiator hose to the radiator assembly, and slide the clamp to secure it.
16057
7.INSTALL RADIATOR HOSE SUB-ASSEMBLY
Install the radiator hose sub-assembly to the radiator assembly and water by-pass pipe, and slide the 2 hose clamps to secure it.
16400
8.INSTALL RADIATOR ASSEMBLY
Install the radiator assembly together with the fan shroud.
Make sure that both lower radiator supports are attached to the fan shroud.
16264D
9.CONNECT NO. 2 WATER BY-PASS HOSE
Connect the No. 2 water by-pass hose to the radiator assembly, and slide the hose clamp to secure it.
16261G
10.CONNECT NO. 1 WATER BY-PASS HOSE
Connect the No. 1 water by-pass hose to the water by-pass pipe, and slide the hose clamp to secure it.
16572D
11.CONNECT NO. 2 RADIATOR HOSE
Connect the No. 2 radiator hose to the water inlet housing, and slide the hose clamp to secure it.
16057
12.CONNECT RADIATOR HOSE SUB-ASSEMBLY
Connect the radiator hose sub-assembly to the No. 1 radiator hose, and slide the hose clamp to secure it.
Install the 2 bolts.
53216A
13.INSTALL UPPER RADIATOR SUPPORT
Install the upper radiator support with the 4 bolts.
16533B
14.INSTALL NO. 1 RADIATOR SUPPORT
Install the 2 No. 1 radiator supports with the 2 bolts.
15.CONNECT WIRE HARNESS
Connect the 2 cooling fan motor connectors.
Attach the 9 wire harness clamps to connect the wire harness.
88706
16.CONNECT LIQUID PIPE SUB-ASSEMBLY
88703
17.CONNECT DISCHARGE HOSE SUB-ASSEMBLY
16681
18.INSTALL RADIATOR UPPER AIR GUIDE PLATE
Install the radiator upper air guide plate with the 6 clips.
52029
19.INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY
Install the front bumper upper reinforcement sub-assembly with the 3 bolts.
Connect the horn connector.
53630
20.CONNECT HOOD LOCK CONTROL CABLE ASSEMBLY
Attach the clamp to connect the hood lock control cable assembly.
53510
21.INSTALL HOOD LOCK ASSEMBLY
53629
22.INSTALL HOOD LOCK CONTROL CABLE COVER (w/ Cover)
74431
23.INSTALL BATTERY TRAY
28800
24.INSTALL BATTERY
74404A
25.INSTALL BATTERY CLAMP SUB-ASSEMBLY
26.CONNECT CABLE TO POSITIVE BATTERY TERMINAL
27.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
28.ADD ENGINE COOLANT
29.INSPECT FOR COOLANT LEAK
30.CHARGE REFRIGERANT
31.WARM UP ENGINE
32.CHECK FOR REFRIGERANT GAS LEAK
16683
33.INSTALL RADIATOR LOWER AIR GUIDE PLATE
Attach the 2 claws and install the radiator lower air guide plate.
52618
34.INSTALL FRONT LOWER BUMPER ABSORBER
Install the front lower bumper absorber with the 4 screws.
51441
35.INSTALL NO. 1 ENGINE UNDER COVER
11212
36.INSTALL NO. 2 CYLINDER HEAD COVER
37.INSTALL HEADLIGHT
for Halogen Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Halogen Headlight)>INSTALLATION
for LED Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>INSTALLATION