Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE(for Dual Type) › from 2015.10
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0059591 SPIRAL CABLE(for Dual Type) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE(for Dual Type)  INSTALLATION  


PROCEDURE

Hide 84306 1.INSTALL SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable sub-assembly with the battery connected and the ignition switch on (IG).

·

Do not rotate the spiral cable sub-assembly with the battery connected and the ignition switch on (IG).

·

Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.



a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the front wheels are facing straight ahead.


d.

Attach the 3 claws to install the spiral cable sub-assembly.

NOTICE:

When replacing the spiral cable sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.



e.

Connect the connector to the spiral cable sub-assembly.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



Hide 45286 2.INSTALL STEERING COLUMN COVER

Hide 3.TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

Hide 84306 4.ADJUST SPIRAL CABLE SUB-ASSEMBLY

NOTICE:

Do not adjust the spiral cable with the battery connected and the ignition switch on (IG).


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B340954C02
0.927,1.313 1.344,1.729 0.417,0.417 0.615,0.969 1.26,1.021 true 0.427,0.865 0.74,1.021 0.313,0.156 10 false *2 0.938,1.323 1.156,1.51 0.219,0.188 10 true *1
*1 Alignment Mark
*2 Colored Roller (Yellow)


Check the check window shown in the illustration.

With the steering wheel straight ahead, align the matchmarks to check the colored roller from the check window.


d.

If the spiral cable sub-assembly is not centered, center it.

i.
B341171C02
1.635,0.771 1.094,0.208 true 0.917,0.083 1.229,0.24 0.313,0.156 10 false *a
*a Interlock


While pushing on the interlock indicated in the illustration, rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:
·

When rotating the spiral cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.




ii.
B341172C02
1.063,0.229 1.688,0.76 true 0.875,0.125 1.188,0.281 0.313,0.156 10 false *a
*a Interlock


While pushing on the interlock indicated in the illustration, rotate the spiral cable sub-assembly 2.5 times clockwise from the lock position.

NOTICE:
·

When rotating the spiral cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.



HINT:

The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.



iii.

Check the check window shown in the illustration.

With the steering wheel straight ahead, align the matchmarks to check the colored roller from the check window.

If the cable cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.



Hide 45100 5.INSTALL STEERING WHEEL ASSEMBLY

Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION