Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY
RM3090E _55 Steering _008773 STEERING COLUMN _0049531 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.


·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 45260 1.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C275622C01
1.792,0.938 1.229,0.323 1.229,0.323 1.885,0.865 true 1.042,0.188 1.354,0.344 0.313,0.156 10 *a
*a Matchmark


Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.


b.

Install the bolt.

Torque:
35.3 N*m (360 kgf*cm, 26 ft.*lbf)


Hide 4520A 2.INSTALL ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY

a.

Install the steering column assembly with the bolt and 2 nuts.

Torque:
for Bolt : 36 N*m (367 kgf*cm, 27 ft.*lbf)
for Nut : 25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

Do not damage the 2 bushings.

·

Do not line-up the bolt hole by prying on the collar or bushings. Only install the bolt straight, without applying any force to the bushings.




b.

Connect the connectors and attach the wire harness clamps to the steering column assembly.


c.

Connect the wire harness with the bolt.

Torque:
8.35 N*m (85 kgf*cm, 74 in.*lbf)


Hide 3.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45260 4.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.

Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft assembly.


b.

Install the bolt.

Torque:
35.3 N*m (360 kgf*cm, 26 ft.*lbf)


Hide 45259A 6.INSTALL COLUMN HOLE COVER SILENCER SHEET

a.

Install the column hole cover silencer sheet with the 2 clips.


b.

Install the floor carpet.


Hide 73900 7.INSTALL NO. 1 LOWER INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55432B 8.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Driver Side Knee Airbag)

Hide 55606 9.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 10.INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

a.

Attach the 3 claws to install the combination switch assembly with spiral cable sub-assembly to the steering column assembly.


b.

Connect the connectors to the combination switch assembly with spiral cable sub-assembly.


Hide 45286 11.INSTALL STEERING COLUMN COVER

a.

Attach the 4 clips, 3 claws and 2 pins to install the upper steering column cover.


b.

Attach the 2 claws to install the lower steering column cover.


c.

Attach the 3 claws.


Hide 45100 12.INSTALL STEERING WHEEL ASSEMBLY

Hide 13.INSPECT STEERING WHEEL CENTER POINT

Hide 14.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 15. INITIALIZE ROTATION ANGLE SENSOR AND CALIBRATE TORQUE SENSOR ZERO POINT