A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
67005B
1.INSTALL BACK DOOR PANEL CUSHION
Attach the 2 claws to install the 2 new back door panel cushions.
Connect the connector and detach the clamp.
68948
2.INSTALL BACK DOOR DAMPER STAY LOWER BRACKET LH (w/o Power Back Door)
68947
3.INSTALL BACK DOOR DAMPER STAY LOWER BRACKET RH (w/o Power Back Door)
Use the same procedure as for the LH side.
68946
4.INSTALL BACK DOOR DAMPER STAY UPPER BRACKET LH (w/o Power Back Door)
68945
5.INSTALL BACK DOOR DAMPER STAY UPPER BRACKET RH (w/o Power Back Door)
Use the same procedure as for the LH side.
68960
6.INSTALL BACK DOOR STAY ASSEMBLY LH (w/o Power Back Door)
68950C
7.INSTALL BACK DOOR STAY ASSEMBLY RH (w/o Power Back Door)
Use the same procedure as for the LH side.
68920
8.INSTALL POWER BACK DOOR UNIT ASSEMBLY SET LH (w/ Power Back Door)
68910A
9.INSTALL POWER BACK DOOR UNIT ASSEMBLY SET RH (w/ Power Back Door)
Use the same procedure as for the LH side.
81690A
10.INSTALL LICENSE PLATE LIGHT ASSEMBLY LH
81270D
11.INSTALL LICENSE PLATE LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
86790
12.INSTALL TELEVISION CAMERA ASSEMBLY (w/ Television Camera)
84840G
13.INSTALL BACK DOOR OPENER SWITCH ASSEMBLY
76802E
14.INSTALL LOWER BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY
76801
15.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY
85035R
16.INSTALL REAR WASHER NOZZLE SUB-ASSEMBLY
76871
17.INSTALL REAR SPOILER
64886B
18.INSTALL BACK DOOR GLASS CHANNEL LH
64885C
19.INSTALL BACK DOOR GLASS CHANNEL RH
Use the same procedure as for the LH side.
20.INSTALL REAR LIGHT ASSEMBLY LH
21.INSTALL REAR LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
84280D
22.INSTALL POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)
84270G
23.INSTALL POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)
Use the same procedure as for the LH side.
85110R
24.INSTALL REAR WIPER MOTOR ASSEMBLY
85169R
25.INSTALL NO. 1 REAR WIPER LINK PIVOT WASHER
26.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY
85192R
27.INSTALL REAR WIPER ARM COVER
89222A
28.INSTALL MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door)
89747
29.INSTALL WIRELESS DOOR LOCK BUZZER (w/ Power Back Door)
69350
30.INSTALL BACK DOOR LOCK ASSEMBLY
84930
31.INSTALL DOOR CONTROL SWITCH ASSEMBLY (w/ Power Back Door)
74811G
32.INSTALL DOOR PULL HANDLE
Attach the 4 claws to install the door pull handle.
67765A
33.INSTALL BACK DOOR NO. 1 SERVICE HOLE COVER
Attach the 4 claws and 4 guides to install the back door No. 1 service hole cover.
67766
34.INSTALL BACK DOOR NO. 2 SERVICE HOLE COVER
Attach the 2 claws and 2 guides to install the back door No. 2 service hole cover.
67848
35.INSTALL BACK DOOR SERVICE HOLE COVER LH
Attach the 2 claws and 2 guides to install the back door service hole cover LH.
67847
36.INSTALL BACK DOOR SERVICE HOLE COVER RH
Use the same procedure as for the LH side.
67750
37.INSTALL BACK DOOR TRIM BOARD ASSEMBLY
Attach the 13 clips to install the back door trim board assembly.
67938A
38.INSTALL BACK DOOR SIDE GARNISH LH
Attach the 2 claws and 2 clips to install the back door side garnish LH.
67937B
39.INSTALL BACK DOOR SIDE GARNISH RH
Use the same procedure as for the LH side.
67939B
40.INSTALL BACK DOOR CENTER GARNISH
Attach the 4 claws and 4 clips to install the back door center garnish.