Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2015.10
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0232444 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1625  Open or Short in Steering Angle Sensor +B  


DESCRIPTION

This DTC is stored if the parking assist ECU receives a signal via CAN communication from the spiral with sensor cable sub-assembly that indicates a power supply system problem.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1625 Open or Short in Steering Angle Sensor +B Open or short in steering angle sensor +B
·

Harness or connector

·

Spiral with sensor cable sub-assembly



WIRING DIAGRAM

E341397E01
1.146,3.219 4.813,3.417 3.667,0.198 10 false : CAN Communication Line 0.927,0.563 2.76,0.76 1.833,0.198 10 false from Battery 0.281,1.156 3.49,1.354 3.208,0.198 10 false from IG1 NO.1 Relay*1 0.365,1.615 1.74,1.958 1.375,0.344 10 false from Engine Stop and Start ECU*2 2.844,2.177 3.302,2.375 0.458,0.198 10 false G12 2.885,2.333 4.406,2.708 1.521,0.375 10 false Spiral with Sensor Cable Sub-assembly 0.083,2.438 5.583,2.635 5.5,0.198 10 false *1: w/o Engine Stop and Start System 0.073,2.813 5.573,3.01 5.5,0.198 10 false *2: w/ Engine Stop and Start System 2.104,0.74 3.635,0.938 1.531,0.198 10 false ECU-B NO.1 2.052,1.323 3.583,1.521 1.531,0.198 10 false ECU-IG NO.1 3.26,0.563 3.719,0.76 0.458,0.198 10 false BAT 3.271,1.156 3.729,1.354 0.458,0.198 10 false IG 3.26,1.771 3.719,1.969 0.458,0.198 10 false ESS 3.01,1.021 3.167,1.219 0.156,0.198 10 false 4 3.01,0.427 3.167,0.625 0.156,0.198 10 false 5 3.031,1.604 3.188,1.802 0.156,0.198 10 false 1 5.365,2.229 7.156,2.51 1.792,0.281 10 false Parking Assist ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Since the panoramic view monitor system has functions that use the CAN communication system, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

·

When "!" mark is displayed on the multi-display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/ Occupant Classification System)>PRECAUTION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.
B106249C27
1.49,0.198 1.979,0.49 0.49,0.292 0.781,1.677 0.938,1.677 0.938,1.677 1.219,1.49 true 2.51,1.885 2.302,1.885 2.302,1.885 1.927,1.51 true 2.802,1.271 2.615,1.271 2.615,1.271 2.26,1.396 true 0.115,0.052 0.615,0.292 0.5,0.24 10 false *a 1.604,0.271 1.958,0.479 0.354,0.208 10 false G12 0.448,1.604 0.865,1.802 0.417,0.198 10 false ESS 2.594,1.802 3.052,2.01 0.458,0.208 10 false IG 2.865,1.198 3.323,1.406 0.458,0.208 10 false BAT
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)


Disconnect the spiral with sensor cable sub-assembly connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE(for Dual Type)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G12-1 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: w/o Engine Stop and Start System

*2: w/ Engine Stop and Start System

G12-4 (IG) - G12-1 (ESS) Engine switch on (IG) 11 to 14 V*1
10 to 16 V*2
G12-5 (BAT) - G12-1 (ESS) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR