The display signal from the rear television camera assembly is transmitted to the navigation receiver assembly*1 or radio and display receiver assembly*2 via the parking assist ECU.
*1: w/ Navigation System
*2: w/ Audio and Visual System (for Radio and Display Type)
When "!" mark is displayed on the multi-display after the battery terminal has been disconnected, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION
Electrical devices are used in the cabin (noise may occur in the image).
The camera lens is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).
The camera lens is dirty with snow, mud, etc.
A strong beam of light, such as a sunbeam or headlight, hits the camera.
It is too dark around the camera (at night, etc.).
The ambient temperature around the camera is either too high or too low.
The vehicle is tilted at a steep angle.
The television camera assembly lens is scratched.
The television camera assembly lens has drops of water on it or the humidity is high.
When the camera is used under fluorescent lights, sodium lights, or mercury lights, etc., the lights and the illuminated area may appear to flicker.
Check if the same malfunction occurs when the panoramic view monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Rear view screen is not displayed. | A |
| Front view screen is not displayed. | B |
| Passenger side monitor screen is not displayed. | C |
| Driver side monitor screen is not displayed. | D |
| Panoramic view monitor screen is not displayed (w/ Navigation System). | E |
| Panoramic view monitor screen is not displayed (w/ Audio and Visual System [for Radio and Display Type]). | F |
A
B
C
D
E
F
Disconnect the a1 parking assist ECU connector.
Disconnect the c3 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a1-3 (CB+) - c3-6 (CB+) | Always | Below 1 Ω |
| a1-1 (CV+) - c3-3 (CV+) | Always | Below 1 Ω |
| a1-2 (CV-) - c3-2 (CV-) | Always | Below 1 Ω |
| a1-9 (CGND) - c3-5 (CGND) | Always | Below 1 Ω |
| a1-3 (CB+) or c3-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| a1-1 (CV+) or c3-3 (CV+) - Body ground | Always | 10 kΩ or higher |
| a1-2 (CV-) or c3-2 (CV-) - Body ground | Always | 10 kΩ or higher |
| a1-9 (CGND) or c3-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Remove the parking assist ECU with the connector still connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a1-9 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| a1-3 (CB+) - a1-9 (CGND) | Engine switch on (IG) | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
Check the waveform of the rear television camera assembly using an oscilloscope.
A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
The video waveform changes according to the image sent by the front television camera assembly.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | a1-1 (CV+) - a1-9 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | ·
Waveform 1: Engine switch on (IG), telltale light assembly (panoramic view monitor main switch) on, camera lens not covered, displaying image ·
Waveform 2: Engine switch on (IG), telltale light assembly (panoramic view monitor main switch) on, camera lens covered, blacking out screen |
Waveform is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the a1 parking assist ECU connector.
Disconnect the Z5 front television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a1-15 (BCB+) - Z5-6 (BCB+) | Always | Below 1 Ω |
| a1-13 (BCV+) - Z5-3 (BCV+) | Always | Below 1 Ω |
| a1-14 (BCV-) - Z5-2 (BCV-) | Always | Below 1 Ω |
| a1-27 (BGND) - Z5-5 (BGND) | Always | Below 1 Ω |
| a1-15 (BCB+) or Z5-6 (BCB+) - Body ground | Always | 10 kΩ or higher |
| a1-13 (BCV+) or Z5-3 (BCV+) - Body ground | Always | 10 kΩ or higher |
| a1-14 (BCV-) or Z5-2 (BCV-) - Body ground | Always | 10 kΩ or higher |
| a1-27 (BGND) or Z5-5 (BGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Remove the parking assist ECU with the connector still connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a1-27 (BGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| a1-15 (BCB+) - a1-27 (BGND) | Engine switch on (IG) | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
Using an oscilloscope, check the waveform.
A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
The video waveform changes according to the image sent by the front television camera assembly.
Waveform is as shown in the illustration.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | a1-13 (BCV+) - a1-27 (BGND) |
| Tool Setting | 200 mV/DIV., 50 μs/DIV. |
| Condition | ·
Waveform 1: Engine switch on (IG), telltale light assembly (panoramic view monitor main switch) on, camera lens not covered, displaying image ·
Waveform 2: Engine switch on (IG), telltale light assembly (panoramic view monitor main switch) on, camera lens covered, blacking out screen |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the a1 parking assist ECU connector.
Disconnect the I14 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a1-6 (RCB+) - I14-5 (RCB+) | Always | Below 1 Ω |
| a1-4 (RCV+) - I14-6 (RCV+) | Always | Below 1 Ω |
| a1-5 (RCV-) - I14-14 (RCV-) | Always | Below 1 Ω |
| a1-18 (RGND) - I14-13 (RGND) | Always | Below 1 Ω |
| a1-6 (RCB+) or I14-5 (RCB+) - Body ground | Always | 10 kΩ or higher |
| a1-4 (RCV+) or I14-6 (RCV+) - Body ground | Always | 10 kΩ or higher |
| a1-5 (RCV-) or I14-14 (RCV-) - Body ground | Always | 10 kΩ or higher |
| a1-18 (RGND) or I14-13 (RGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Remove the parking assist ECU with the connector still connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a1-18 (RGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| a1-6 (RCB+) - a1-18 (RGND) | Engine switch on (IG) | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
Measure the waveform of the side television camera assembly RH using an oscilloscope.
A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
The video waveform changes according to the image sent by the front television camera assembly.
| Item | Content |
|---|---|
| Tester Connection | a1-4 (RCV+) - a1-18 (RGND) |
| Tool Setting | 200 mV/DIV., 50 μs/DIV. |
| Condition | ·
Waveform 1: Engine switch on (IG), telltale light assembly (panoramic view monitor main switch) on, camera lens not covered, displaying image ·
Waveform 2: Engine switch on (IG), telltale light assembly (panoramic view monitor main switch) on, camera lens covered, blacking out screen |
Waveform is as shown in illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly RH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL
Check if the same malfunction reoccurs when the side monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Malfunction does not reoccur (returns to normal) | A |
| Malfunction reoccurs | B |
A
B
Disconnect the a1 parking assist ECU connector.
Disconnect the J14 outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a1-12 (LCB+) - J14-5 (LCB+) | Always | Below 1 Ω |
| a1-10 (LCV+) - J14-6 (LCV+) | Always | Below 1 Ω |
| a1-11 (LCV-) - J14-14 (LCV-) | Always | Below 1 Ω |
| a1-24 (LGND) - J14-13 (LGND) | Always | Below 1 Ω |
| a1-12 (LCB+) or J14-5 (LCB+) - Body ground | Always | 10 kΩ or higher |
| a1-10 (LCV+) or J14-6 (LCV+) - Body ground | Always | 10 kΩ or higher |
| a1-11 (LCV-) or J14-14 (LCV-) - Body ground | Always | 10 kΩ or higher |
| a1-24 (LGND) or J14-13 (LGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Remove the parking assist ECU with the connector still connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a1-24 (LGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| a1-12 (LCB+) - a1-24 (LGND) | Engine switch on (IG) | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Wavehorm | - | - |
Measure the waveform of the side television camera assembly LH using an oscilloscope.
A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
The video waveform changes according to the image sent by the front television camera assembly.
| Item | Content |
|---|---|
| Tester Connection | a1-10 (LCV+) - a1-24 (LGND) |
| Tool Setting | 200 mV/DIV., 50 μs/DIV. |
| Condition | ·
Waveform 1: Engine switch on (IG), telltale light assembly (panoramic view monitor main switch) on, camera lens not covered, displaying image ·
Waveform 2: Engine switch on (IG), telltale light assembly (panoramic view monitor main switch) on, camera lens covered, blacking out screen |
Waveform is as shown in illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly LH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL
Check if the same malfunction reoccurs when the side monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Malfunction does not reoccur (returns to normal) | A |
| Malfunction reoccurs | B |
A
B
Disconnect the a2 parking assist ECU connector.
Disconnect the G158 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a2-26 (NS-) - G158-24 (V-) | Always | Below 1 Ω |
| a2-28 (NS+) - G158-12 (V+) | Always | Below 1 Ω |
| G158-23 (CGND) - Body ground | Always | Below 1 Ω |
| a2-26 (NS-) or G158-24 (V-) - Body ground | Always | 10 kΩ or higher |
| a2-28 (NS+) or G158-12 (V+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the navigation receiver assembly with a new or normally functioning one.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL
Check if the same malfunction reoccurs when the panoramic view monitor screen is displayed.
Malfunction does not reoccur (returns to normal).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the a2 parking assist ECU connector.
Disconnect the G159 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a2-26 (NS-) - G159-24 (V-) | Always | Below 1 Ω |
| a2-28 (NS+) - G159-12 (V+) | Always | Below 1 Ω |
| G159-23 (CGND) - Body ground | Always | Below 1 Ω |
| a2-26 (NS-) or G159-24 (V-) - Body ground | Always | 10 kΩ or higher |
| a2-28 (NS+) or G159-12 (V+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the radio and display receiver assembly with a new or normally functioning one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL
Check if the same malfunction reoccurs when the panoramic view monitor screen is displayed.
Malfunction does not reoccur (returns to normal).
| Proceed to |
|---|
| OK |
| NG |
OK
NG