Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.10
RM3090E _58 Vehicle Interior _044382 PRE-CRASH SAFETY _0224751 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A11  Front Radar Sensor Incorrect Axial Gap  C1A14  Front Radar Sensor Beam Axis Not Adjusted  


DESCRIPTION

The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.

Based on this information, the driving support ECU assembly sends pre-crash control operation signals.

When the vehicle is determined to be driving in a straight line or on a gradual curve based on signals from the airbag sesor assembly etc., the millimeter wave radar sensor assembly performs self-diagnosis to check if the sensor beam axis has deviated from the vehicle movement direction. When the millimeter wave radar sensor assembly beam axis has deviated, the driving support ECU assembly detects this, and stores DTC C1A11.

After installing a new millimeter wave radar sensor assembly, if sensor beam axis adjustment is not performed, DTC C1A14 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A11 Front Radar Sensor Incorrect Axial Gap While the ignition switch is ON, misalignment of the millimeter wave radar sensor assembly is detected for approximately 0.2 seconds.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly


C1A14 Front Radar Sensor Beam Axis Not Adjusted When the vehicle is being driven at a speed of 10 km/h (6 mph) or more, misalignment of the millimeter wave radar sensor assembly is detected for approximately 0.2 seconds.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the driving support ECU assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle, and as a result, a DTC may be stored.



PROCEDURE

1.CHECK FOR DTCs
a.

Check if the stored DTCs are current DTCs.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Enter the following menus: Powertrain / Radar Cruise2 / Trouble Codes.

Click here


e.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
Current DTC C1A11 is output A
Current DTC C1A14 is output B
History DTC C1A11 is output C



A

2.CHECK VEHICLE CONDITION

B

13.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

C

17.CLEAR DTC
2.CHECK VEHICLE CONDITION
a.

Check the operating conditions of the vehicle.

HINT:

DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is temporarily misaligned due to the vehicle being overloaded.



Result:
Result Proceed to
Vehicle is not overloaded or being towed. A
Vehicle is overloaded or being towed. B



A

3.CHECK WHEEL ALIGNMENT

B

12.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
3.CHECK WHEEL ALIGNMENT
a.

Check the front and rear wheel alignment (toe).

for front wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT

for rear wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT

HINT:

DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is misaligned due to incorrect wheel alignment (toe).



Result:
Result Proceed to
Front or rear wheel is misaligned (toe) A
Front and rear wheels are not misaligned (toe) B



A

4.ADJUST WHEEL ALIGNMENT

B

7.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
4.ADJUST WHEEL ALIGNMENT
a.

Adjust the alignment (toe) of the wheels.

for front wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT

for rear wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCs
6.CHECK FOR DTCs
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the ignition switch to ON.

2.

Turn the dynamic radar cruise control system on using the cruise control switch (ON/OFF).

3.

Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.




c.

Check for DTCs.

Click here

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A11 is not output A
DTC C1A11 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

8.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
7.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Check that the bracket of the millimeter wave radar sensor assembly is not deformed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


Result:
Result Proceed to
Bracket is not deformed A
No. 1 millimeter wave radar sensor bracket is deformed B
The other bracket than No. 1 millimeter wave radar sensor bracket is deformed C



A

5.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

10.REPLACE NO. 1 MILLIMETER WAVE RADAR SENSOR BRACKET

C

8.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
8.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTCs
9.CHECK FOR DTCs
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the ignition switch to ON.

2.

Turn the dynamic radar cruise control system on using the cruise control switch (ON/OFF).

3.

Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A11 is not output A
DTC C1A11 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

10.REPLACE NO. 1 MILLIMETER WAVE RADAR SENSOR BRACKET
a.

Replace the No. 1 millimeter wave radar sensor bracket with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DISASSEMBLY


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTCs
11.CHECK FOR DTCs
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the ignition switch to ON.

2.

Turn the dynamic radar cruise control system on using the cruise control switch (ON/OFF).

3.

Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A11 is not output A
DTC C1A11 is output B



A

END (NO. 1 MILLIMETER WAVE RADAR SENSOR BRACKET WAS DEFECTIVE)

B

12.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Return the vehicle to normal operating conditions.


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


c.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)>DTC CHECK / CLEAR

Chassis > LKA/LDA > Clear DTCs
50002 355
NOTICE:
·

When the vehicle is overloaded or towing something, it may not be possible to perform beam axis adjustment of the millimeter wave radar sensor assembly.

·

After clearing the DTCs, if the vehicle is overloaded or towing something, do not use the system.

·

The 2 conditions listed above do not indicate a malfunction of the millimeter wave radar sensor assembly.




Result:
Proceed to
NEXT



NEXT

END

13.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

14.CHECK FOR DTCs
14.CHECK FOR DTCs
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the ignition switch to ON

2.

Turn the dynamic radar cruise control system on using the cruise control switch (ON/OFF).

3.

Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A14 is not output A
DTC C1A14 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

15.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
15.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

16.CHECK FOR DTCs
16.CHECK FOR DTCs
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the ignition switch to ON.

2.

Turn the dynamic radar cruise control system on using the cruise control switch (ON/OFF).

3.

Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A14 is not output A
DTC C1A14 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

17.CLEAR DTC
a.

Check for DTCs related to misalignment of millimeter wave radar sensor assembly.

HINT:

If only history DTCs are stored, they may have stored due to a temporarily condition such as overloading of the vehicle, and the system returned to normal when beam axis learning was performed.



b.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

Result:
Proceed to
NEXT



NEXT

END