Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.10
RM3090E _58 Vehicle Interior _044382 PRE-CRASH SAFETY _0224751 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A47  Steering Angle Sensor  


DESCRIPTION

The brake actuator assembly (skid control ECU) receives steering rotation angle information from the spiral with sensor cable sub-assembly (steering angle sensor), and sends the information to the driving support ECU assembly via CAN communication.

If the brake actuator assembly (skid control ECU) detects a malfunction of the spiral with sensor cable sub-assembly (steering angle sensor), it sends a malfunction signal to the driving support ECU assembly and stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A47 Steering Angle Sensor While the vehicle speed is 50 km/h (31 mph) or more, a spiral with sensor cable sub-assembly (steering angle sensor) malfunction signal is received from the brake actuator assembly (skid control ECU) for 1 second or more.
·

Vehicle stability control system

·

Brake actuator assembly (Skid control ECU)

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.


e.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
OK:

Vehicle stability control system DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTC

NG

2.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met (drive the vehicle at a speed of 50 km/h [31 mph] or more).

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
OK:

DTC C1A47 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met (drive the vehicle at a speed of 50 km/h [31 mph] or more).

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
OK:

DTC C1A47 is not output.



Result:
Proceed to
OK
NG



OK

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)