Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.10
RM3090E _58 Vehicle Interior _044382 PRE-CRASH SAFETY _0224751 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

Based on pre-crash control, the driving support ECU assembly provides warnings to the driver. The driving support ECU assembly does this by sending a request signal to the millimeter wave radar sensor assembly to sound the skid control buzzer.

When the millimeter wave radar sensor assembly detects a malfunction in the skid control buzzer circuit, a malfunction signal is sent to the driving support ECU assembly, and this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A Skid Control Buzzer Circuit While the ignition switch is ON, and the pre-crash alarm control is operating, either of the following conditions is met:
·

A buzzer request signal is sent to the skid control buzzer but the buzzer does not sound for 1 second or more.

·

A buzzer request signal is not sent to the skid control buzzer but the buzzer sounds for 1 second or more.


·

Harness or connector

·

Skid control buzzer

·

Driving support ECU assembly



WIRING DIAGRAM

E341242E02
0.198,1.042 1.594,1.24 1.396,0.198 10 false from IG1 NO.1 Relay 0.76,0.479 2.156,0.865 1.396,0.385 10 false from Engine Stop and Start ECU 2.531,0.365 2.719,0.542 0.188,0.177 10 false *1 1.865,0.938 2.052,1.115 0.188,0.177 10 false *2 2.188,1.229 3.094,1.438 0.906,0.208 10 false ECU-IG NO.2 3.385,0.927 3.542,1.104 0.156,0.177 10 false 2 3.583,1.042 3.844,1.229 0.26,0.188 10 false IG1 4.25,1.042 4.51,1.229 0.26,0.188 10 false BZ 4.5,0.927 4.656,1.104 0.156,0.177 10 false 1 3.438,1.417 3.75,1.615 0.313,0.198 10 false G74 3.438,1.594 4.729,1.813 1.292,0.219 10 false Skid Control Buzzer 5.323,0.927 5.479,1.104 0.156,0.177 10 false 3 5.552,1.052 5.906,1.24 0.354,0.188 10 false BZ 5.083,2.083 5.438,2.271 0.354,0.188 10 false G168 5.094,2.25 7.042,2.469 1.948,0.219 10 false Driving Support ECU Assembly 0.104,2.427 2.094,2.698 1.99,0.271 10 false *2: w/o Stop and Start System 0.104,2.094 2.094,2.365 1.99,0.271 10 false *1: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer ON/OFF Test possible with ignition switch ON, vehicle stopped
Body Electrical > Pre-Crash 2 > Active Test
Tester Display
PCS Crash Alarm Buzzer
50004 220 5

c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
OK:

DTC C1A4A is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - BATTERY)
2.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - BATTERY)
a.
B338290C80
0.583,1.281 1.083,1.531 0.5,0.25 2.417,2 2.167,2 2.167,2 1.896,1.604 true 0.063,0.094 0.323,0.229 0.26,0.135 10 false *a 0.708,1.313 1.063,1.521 0.354,0.208 10 false G74 2.469,1.927 2.917,2.146 0.448,0.219 10 false IG1
*a Front view of wire harness connector
(to Skid Control Buzzer)


Disconnect the skid control buzzer connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

*1: w/o Stop and Start System

*2: w/ Stop and Start System

G74-2 (IG1) - Body ground Ignition switch ON 11 to 14 V*1
9.5 to 14 V*2
G74-2 (IG1) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - DRIVING SUPPORT ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the G74 skid control buzzer connector.


b.

Disconnect the G168 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G74-1 (BZ) - G168-3 (BZ) Always Below 1 Ω
G74-1 (BZ) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT SKID CONTROL BUZZER (CONFIRM BUZZER OPERATION)

NG

4.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer ON/OFF Test possible with ignition switch ON, vehicle stopped
Body Electrical > Pre-Crash 2 > Active Test
Tester Display
PCS Crash Alarm Buzzer
50004 220 5

c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
OK:

DTC C1A4A is not output.



Result:
Proceed to
OK
NG



OK

END (HARNESS OR CONNECTOR WAS DEFECTIVE)

NG

6.INSPECT SKID CONTROL BUZZER (CONFIRM BUZZER OPERATION)
6.INSPECT SKID CONTROL BUZZER (CONFIRM BUZZER OPERATION)
a.

Turn the ignition switch to ON.


b.

Check if the skid control buzzer assembly is sounding.


Result:
Result Proceed to
The skid control buzzer assembly does not sound when the ignition switch is to ON A
The skid control buzzer assembly sounds continuously when the ignition switch is to ON B



A

7.INSPECT SKID CONTROL BUZZER (UNIT INSPECTION)

B

8.REPLACE SKID CONTROL BUZZER
7.INSPECT SKID CONTROL BUZZER (UNIT INSPECTION)
a.

b.

Result:
Result Proceed to
Skid control buzzer assembly is abnormal A
Skid control buzzer assembly is normal B



A

8.REPLACE SKID CONTROL BUZZER

B

9.CHECK FOR DTCs
8.REPLACE SKID CONTROL BUZZER
a.

Replace the skid control buzzer assembly.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM WARNING BUZZER>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTCs
9.CHECK FOR DTCs
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Perform the Active Test according to the display on the GTS.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST

NOTICE:

Perform the Active Test for 1 second or more.


HINT:

Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.


Body Electrical > Pre-Crash 2 > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer assembly ON / OFF Test possible with ignition switch to ON, vehicle stopped

c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220

Result:
Result Proceed to
DTC C1A4A is not output A
DTC C1A4A is output B



A

END (SKID CONTROL BUZZER WAS DEFECTIVE)

B