Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.10
RM3090E _58 Vehicle Interior _044382 PRE-CRASH SAFETY _0224751 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A50  Brake System  


DESCRIPTION

When the pre-crash safety system is operating, the driving support ECU assembly sends brake control signals to the brake actuator assembly (skid control ECU).

When the driving support ECU assembly receives a VSC system malfunction signal from the brake actuator assembly (skid control ECU) via CAN communication, DTC C1A50 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A50 Brake System While the ignition switch is ON, the driving support ECU assembly receives a VSC system malfunction signal from the brake actuator assembly (skid control ECU) for 0.2 seconds or more.
·

Vehicle stability control system

·

Brake actuator assembly (skid control ECU)

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.



PROCEDURE

1.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.


e.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
Electronically controlled brake system DTCs are not output A
Electronically controlled brake system DTCs are output B




A

2.CHECK FOR DTC

B

2.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
OK:

DTC C1A50 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
3.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.



c.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
OK:

DTC C1A50 is not output.



Result:
Proceed to
OK
NG



OK

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)