Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › from 2015.10
RM3090E _58 Vehicle Interior _008789 HEATING / AIR CONDITIONING _0049188 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  ECO Switch Circuit  


DESCRIPTION

When the combination switch assembly (ECO mode switch) is turned on, the air conditioning amplifier assembly receives a combination switch assembly (ECO mode switch) ON signal and controls the air conditioning to enhance fuel efficiency.

WIRING DIAGRAM

E261769E20
4.802,1.833 5.25,2.083 0.448,0.25 10 false G81 4.813,2 6.417,2.354 1.604,0.354 10 false Air Conditioning Amplifier Assembly 4.729,0.573 4.979,0.76 0.25,0.188 10 false 24 5.021,0.688 5.438,0.833 0.417,0.146 10 false ECOS 2.24,0.604 2.948,0.771 0.708,0.167 10 false 3*1, 4*2 1.833,0.594 2.167,0.771 0.333,0.177 10 false ECU 2.24,1.229 2.865,1.375 0.625,0.146 10 false 4*1, 6*2 1.688,1.229 2.167,1.396 0.479,0.167 10 false MSW2 0.167,1.99 3.354,2.25 3.188,0.26 10 false Combination Switch Assembly (ECO Mode Switch) 0.167,1.813 1.563,2.01 1.396,0.198 10 false G60*1, G185*2 0.125,2.406 2.302,2.635 2.177,0.229 10 false *1: w/o Stop and Start System 2.219,2.385 4.25,2.604 2.031,0.219 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

When the battery is disconnected or the air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the values by referring to the table below.


Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ECO Switch Combination switch assembly (ECO mode switch) OFF or ON OFF: Combination switch assembly (ECO mode switch) not operated
ON: Combination switch assembly (ECO mode switch) operated
-
Body Electrical > Air Conditioner > Data List
Tester Display
ECO Switch
50003 121 163
OK:

Combination switch assembly (ECO mode switch) condition displayed on the GTS changes with the actual switch operation.


Result:
Proceed to
OK
NG



OK

NG

2.INSPECT COMBINATION SWITCH ASSEMBLY (ECO MODE SWITCH)
2.INSPECT COMBINATION SWITCH ASSEMBLY (ECO MODE SWITCH)
a.

Remove the combination switch assembly (ECO mode switch).



b.

Inspect the combination switch assembly (ECO mode switch).



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY [ECO MODE SWITCH] - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPLACE COMBINATION SWITCH ASSEMBLY (ECO MODE SWITCH)

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY [ECO MODE SWITCH] - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the G81 air conditioning amplifier assembly connector.


b.

Disconnect the G60*1 or G185*2 combination switch assembly (ECO mode switch) connector.

*1: w/o Stop and Start System

*2: w/ Stop and Start System



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Stop and Start System:
Tester Connection Condition Specified Condition
G81-24 (ECOS) - G60-3 (ECU) Always Below 1 Ω
G81-24 (ECOS) - Body ground Always 10 kΩ or higher

w/ Stop and Start System:
Tester Connection Condition Specified Condition
G81-24 (ECOS) - G185-4 (ECU) Always Below 1 Ω
G81-24 (ECOS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY [ECO MODE SWITCH] - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY [ECO MODE SWITCH] - BODY GROUND)
a.
E340655C01
0.333,0.75 0.833,1.083 0.5,0.333 0.167,2.417 0.667,2.75 0.5,0.333 1.938,1.208 2.104,1.625 2.104,1.625 2.438,1.625 true 2.01,2.75 2.177,3.167 2.177,3.167 2.51,3.167 true 0.042,0.042 0.354,0.24 0.313,0.198 10 false *a 2.479,1.521 3,1.719 0.521,0.198 10 false MSW2 2.583,3.073 3.104,3.271 0.521,0.198 10 false MSW2 0.448,0.833 0.969,1.031 0.521,0.198 10 false G60 0.885,0.823 1.406,1.021 0.521,0.198 10 false *A 0.24,2.49 0.76,2.688 0.521,0.198 10 false G185 0.719,2.479 1.24,2.677 0.521,0.198 10 false *B
*A w/o Stop and Start System
*B w/ Stop and Start System
*a Front view of wire harness connector
(to Combination Switch Assembly [ECO Mode Switch])


Disconnect the combination switch assembly (ECO mode switch) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Stop and Start System:
Tester Connection Condition Specified Condition
G60-4 (MSW2) - Body ground Always Below 1 Ω

w/ Stop and Start System:
Tester Connection Condition Specified Condition
G185-6 (MSW2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR