Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › from 2015.10
RM3090E _58 Vehicle Interior _008789 HEATING / AIR CONDITIONING _0049189 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1451  Compressor Solenoid Circuit  


DESCRIPTION

In this circuit, the compressor assembly with pulley (compressor solenoid) receives a refrigerant compression demand signal from the air conditioning amplifier assembly.

Based on this signal, the compressor assembly with pulley (compressor solenoid) changes the amount of compressor output.


DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1451 Compressor Solenoid Circuit Open or short in compressor solenoid circuit
·

Compressor assembly with pulley (compressor solenoid)

·

Harness or connector

·

Air conditioning amplifier assembly


-

WIRING DIAGRAM

E229254E69
4.969,0.792 5.156,0.969 0.188,0.177 10 false 11 3.833,0.802 3.927,0.979 0.094,0.177 10 false 2 2.448,0.802 2.542,0.979 0.094,0.177 10 false 1 5.208,0.906 5.667,1.083 0.458,0.177 10 false SOL+ 3.385,0.99 3.76,1.167 0.375,0.177 10 false SOL+ 2.604,1 2.948,1.177 0.344,0.177 10 false SOL- 4.854,3.531 5.198,3.708 0.344,0.177 10 false G80 4.865,3.698 6.51,4.031 1.646,0.333 10 false Air Conditioning Amplifier Assembly 2.25,1.5 4.365,1.823 2.115,0.323 10 false Compressor Assembly with Pulley (Compressor Solenoid) 2.25,1.333 3.49,1.51 1.24,0.177 10 false B30*1, B116*2 0.135,3.917 1.375,4.094 1.24,0.177 10 false *1: except 2WW 0.146,4.229 1.385,4.406 1.24,0.177 10 false *2: for 2WW

PROCEDURE

1.INSPECT COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID)

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SOL-) - 2 (SOL+) 20°C (68°F) 10.1 to 11.1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY [COMPRESSOR SOLENOID] - BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY [COMPRESSOR SOLENOID] - BODY GROUND)
a.
E340654C01
0.333,0.667 0.833,1 0.5,0.333 0.333,2.333 0.833,2.667 0.5,0.333 1.094,1.458 1.344,1.458 1.344,1.458 1.5,1 true 2.417,2.917 2.167,2.917 2.167,2.917 1.844,2.531 true 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a 0.729,1.375 1.188,1.563 0.458,0.188 10 false SOL- 2.469,2.833 2.927,3.021 0.458,0.188 10 false SOL- 0.469,0.75 0.927,0.938 0.458,0.188 10 false B30 0.875,0.74 1.333,0.927 0.458,0.188 10 false *A 0.427,2.406 0.885,2.594 0.458,0.188 10 false B116 0.917,2.406 1.375,2.594 0.458,0.188 10 false *B
*A except 2WW
*B for 2WW
*a Front view of wire harness connector
(to Compressor Assembly with Pulley)


Disconnect the compressor assembly with pulley (compressor solenoid) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except 2WW:
Tester Connection Condition Specified Condition
B30-1 (SOL-) - Body ground Always Below 1 Ω

for 2WW:
Tester Connection Condition Specified Condition
B116-1 (SOL-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COMPRESSOR ASSEMBLY WITH PULLEY [COMPRESSOR SOLENOID])

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COMPRESSOR ASSEMBLY WITH PULLEY [COMPRESSOR SOLENOID])
a.

Disconnect the G80 air conditioning amplifier assembly connector.


b.

Disconnect the B30*1 or B116*2 compressor with pulley assembly (compressor solenoid) connector.

*1: except 2WW

*2: for 2WW



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
except 2WW:
Tester Connection Condition Specified Condition
G80-11 (SOL+) - B30-2 (SOL+) Always Below 1 Ω
G80-11 (SOL+) - Body ground Always 10 kΩ or higher

for 2WW:
Tester Connection Condition Specified Condition
G80-11 (SOL+) - B116-2 (SOL+) Always Below 1 Ω
G80-11 (SOL+) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR