Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR › from 2015.10
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0050508 REAR AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89834 1.INSTALL REAR AIRBAG SENSOR LH

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Insert the pin (stopper) into the body hole to install the rear airbag sensor to the vehicle with the nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the rear airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the pin (stopper) is securely inserted into the body hole.

·

Tighten the nut while holding the rear airbag sensor because the rear airbag sensor pin (stopper) is easily damaged.




d.

Connect the connector to the rear airbag sensor LH.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

While holding the outer housing, be sure to engage the connectors until they are locked and check that the outer housing is in its original position (when locking, make sure that a click sound can be heard).

C198070C08
5.594,1.219 5.365,0.635 false 3.479,0.979 3.313,0.563 false 3.198,0.406 3.51,0.563 0.313,0.156 10 *1 5.24,0.458 5.552,0.615 0.313,0.156 10 *1
*1 Outer Housing - -




e.

Check that there is no looseness in the installation parts of the rear airbag sensor LH.


Hide 64740E 2.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

Hide 64718A 3.INSTALL DECK TRIM SERVICE HOLE COVER

Hide 62332C 4.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 67918E 5.INSTALL REAR DOOR SCUFF PLATE LH

Hide 58577E 6.INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (w/o Spare Tire, for Compact Spare Tire)

Hide 58577E 7.INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (w/ Grand Spare Tire)

Hide 58386 8.INSTALL REAR FLOOR FINISH PLATE (w/o Spare Tire, for Compact Spare Tire)

Hide 64716P 9.INSTALL REAR DECK TRIM COVER (w/ Grand Spare Tire)

Hide 58417H 10.INSTALL REAR NO. 3 FLOOR BOARD

Hide 64997 11.INSTALL DECK FLOOR BOX LH

Hide 58410B 12.INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire, for Compact Spare Tire)

Hide 58410B 13.INSTALL DECK BOARD ASSEMBLY (w/ Grand Spare Tire)

Hide 64910N 14.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 64309A 15.INSTALL PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY (w/ Partition Net)

Hide 16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION