Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR(for 2WW) › from 2016.08
RM3090E _58 Vehicle Interior _008789 HEATING / AIR CONDITIONING _0208269 COMPRESSOR(for 2WW) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 2WW)  INSTALLATION  


PROCEDURE

Hide 1.INSPECT COMPRESSOR OIL

a.
E332767

When replacing the compressor assembly with pulley with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor assembly with pulley before installation.

Standard:

(Oil capacity inside the new compressor assembly with pulley: 70 to 85 cc (2.37 to 2.87 fl.oz)) - (Remaining oil amount in the removed compressor assembly with pulley) = (Oil amount to be removed from the new compressor)


NOTICE:
·

If a new compressor assembly with pulley is installed without removing some oil, there will be too much oil in the system due to the oil remaining in the pipes of the vehicle. Excessive oil in the system prevents heat exchange in the refrigeration cycle and causes ineffective cooling.

·

If the amount of oil remaining in the old compressor assembly with pulley is too small, check the air conditioning system for oil leaks.

·

for HFC-134a(R134a): Make sure to use ND-OIL 8 or equivalent compressor oil.

·

for HFO-1234yf(R1234yf): Make sure to use ND-OIL 12 or equivalent compressor oil.




Hide 88310 2.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

a.
E332768C01
1.042,1.042 1.354,1.198 0.313,0.156 10 false *a
*a Protrusion Height


Using a plastic-faced hammer, tap in a new compressor pin.

Standard protrusion height:

3.5 to 4.5 mm (0.1378 to 0.1772 in.)



b.

Using an E8 "TORX" socket wrench, install the 2 stud bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


c.
E332765N01
1.031,1.875 1.219,2.073 0.188,0.198 10 true (1) 0.635,1.458 0.823,1.656 0.188,0.198 10 true (2) 1.469,1.729 1.656,1.927 0.188,0.198 10 true (3)

Tighten the 2 nuts and bolt in the order shown in the illustration to install the compressor assembly with pulley.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


d.

Attach the clamp to connect the wire harness.


e.

Connect the connector.


Hide 88703 3.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the discharge hose sub-assembly and compressor assembly with pulley.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge hose sub-assembly.

Refrigerant Compressor Oil
HFC-134a (R134a) ND-OIL 8 or equivalent
HFO-1234yf (R1234yf) ND-OIL 12 or equivalent


c.

Install the O-ring to the discharge hose sub-assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.

Connect the discharge hose sub-assembly to the compressor assembly with pulley with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88704 4.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction hose sub-assembly and compressor assembly with pulley.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.

Refrigerant Compressor Oil
HFC-134a (R134a) ND-OIL 8 or equivalent
HFO-1234yf (R1234yf) ND-OIL 12 or equivalent


c.

Install the O-ring to the suction hose sub-assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.

Connect the suction hose sub-assembly to the compressor assembly with pulley with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 16400 6.INSTALL RADIATOR ASSEMBLY

Hide 7. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT