16058
1.INSTALL NO. 2 RADIATOR HOSE SUB-ASSEMBLY
Attach the clamp to install the No. 2 radiator hose sub-assembly to the fan shroud.
16711
2.INSTALL FAN SHROUD
Install the fan shroud with the 3 bolts.
17940D
3.INSTALL INTERCOOLER ASSEMBLY
16534
4.INSTALL NO. 2 RADIATOR SUPPORT
88460
5.INSTALL COOLER CONDENSER ASSEMBLY
16533
6.INSTALL UPPER RADIATOR SUPPORT
Install the 2 upper radiator supports with the 4 bolts.
16572D
7.INSTALL NO. 2 RADIATOR HOSE
Install the No. 2 radiator hose to the radiator assembly and slide the clamp to secure the hose.
17362B
8.INSTALL NO. 2 AIR TUBE
Install the No. 2 air tube to the intercooler assembly and No. 2 radiator support with the bolt.
Tighten the hose clamp to secure the No. 2 air tube.
16400
9.INSTALL RADIATOR ASSEMBLY
Install the 2 cushions.
Install the radiator assembly together with the intercooler assembly to the vehicle.
Do not allow the radiator assembly to interfere with other parts.
16572D
10.CONNECT NO. 2 RADIATOR HOSE
Check that the retainer is closed when the connector is inserted.
If replacing the hose, apply fresh engine coolant to the O-ring.
Push on the connector until it makes a click sound which indicates that the connection is complete. After connecting the connector, check that the connector cannot be disconnected by pulling the connector.
Do not use a quick connector that has been dropped.
Push in the retainer and connect the No. 2 radiator hose to the water inlet.
17343D
11.INSTALL NO. 3 AIR HOSE
Connect the No. 3 air hose to the No. 2 air tube and tighten the hose clamp to secure the hose.
17342D
12.INSTALL NO. 2 AIR HOSE
If replacing the intercooler air hose, check for deposits in the intercooler assembly and intercooler air hose. If necessary, wipe up deposits.
Connect the No. 2 air hose to the intercooler assembly and tighten the hose clamp to secure the hose.
16571C
13.CONNECT NO. 1 RADIATOR HOSE
Connect the No. 1 radiator hose to the radiator assembly and slide the hose clamp to secure the hose.
16058
14.CONNECT NO. 2 RADIATOR HOSE SUB-ASSEMBLY
Connect the No. 2 radiator hose sub-assembly to the radiator assembly and slide the hose clamp to secure the hose.
16282
15.CONNECT NO. 5 WATER BY-PASS HOSE
Attach the clamp to connect the No. 5 water by-pass hose to the fan shroud.
Connect the No. 5 water by-pass hose to the radiator assembly and slide the hose clamp to secure the hose.
53205
16.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY
Install the upper radiator support sub-assembly with the 4 bolts.
53510
17.INSTALL HOOD LOCK ASSEMBLY
18.CONNECT WIRE HARNESS
Connect the 3 connectors and attach the 10 wire harness clamps to connect the wire harness to the radiator assembly and fan shroud.
16260
19.CONNECT WATER BY-PASS HOSE ASSEMBLY
Attach the hose clamp to connect the No. 5 water by-pass hose clamp to the hose clamp bracket.
Connect the water by-pass hose assembly to the upper radiator support sub-assembly with the bolt.
Connect the water by-pass hose to the reservoir assembly and slide the clamp to secure the hose.
16533B
20.INSTALL NO. 1 RADIATOR SUPPORT
Install the 2 radiator support cushions.
Install the 2 No. 1 radiator supports with the 2 bolts.
16697A
21.INSTALL REAR RADIATOR SIDE AIR GUIDE PLATE LH
Install the rear radiator side air guide plate LH with the 2 clips.
16695A
22.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE LH
Install the front radiator side air guide plate LH and attach the 3 claws.
16693A
23.INSTALL REAR RADIATOR SIDE AIR GUIDE PLATE RH
Install the rear radiator side air guide plate RH with the 2 clips.
16691A
24.INSTALL FRONT RADIATOR SIDE AIR GUIDE PLATE RH
Install the front radiator side air guide plate RH and attach the 3 claws.
88706
25.CONNECT LIQUID TUBE SUB-ASSEMBLY (w/ Air Conditioning System)
Remove the attached vinyl tape from the liquid tube sub-assembly and connecting part of the cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the tube joint.
Compressor oil ND-OIL 8 or equivalent
Compressor oil ND-OIL 12 or equivalent
Connect the liquid tube sub-assembly to the cooler condenser assembly with the bolt.
88703
26.CONNECT DISCHARGE HOSE SUB-ASSEMBLY (w/ Air Conditioning System)
Remove the attached vinyl tape from the discharge hose sub-assembly and connecting part of the cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.
Compressor oil ND-OIL 8 or equivalent
Compressor oil ND-OIL 12 or equivalent
Connect the discharge hose sub-assembly to the cooler condenser assembly with the bolt.
52131A
27.INSTALL FRONT BUMPER REINFORCEMENT
16683A
28.INSTALL LOWER RADIATOR AIR GUIDE PLATE
Install the lower radiator guide plate and attach the 3 claws.
16681A
29.INSTALL UPPER RADIATOR AIR GUIDE PLATE
Install the upper radiator air guide plate with 6 clips.
52029
30.INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY
Install the front bumper upper reinforcement sub-assembly with the 2 bolts and 2 clips.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
Connect the connector to the horn.
52085
31.INSTALL FRONT BUMPER CENTER STAY SUB-ASSEMBLY
Install the front bumper center stay sub-assembly with the 2 bolts.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
Connect the connector to the horn.
74414B
32.INSTALL BATTERY BRACKET REINFORCEMENT
74410
33.INSTALL BATTERY CARRIER ASSEMBLY
74431
34.INSTALL BATTERY TRAY
28800
35.INSTALL BATTERY
28899
36.INSTALL BATTERY INSULATOR
74404A
37.INSTALL BATTERY CLAMP SUB-ASSEMBLY
52618
38.INSTALL FRONT LOWER BUMPER ABSORBER
Install the front lower bumper absorber with the 4 screws.
39.INSTALL HEADLIGHT ASSEMBLY
for Halogen Headlight
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Halogen Headlight)>INSTALLATION
for LED Headlight
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>INSTALLATION
40.CONNECT CABLE TO POSITIVE BATTERY TERMINAL
41.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
42.ADD ENGINE COOLANT
43.CHARGE REFRIGERANT (w/ Air Conditioning System)
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFO-1234yf(R1234yf))>REPLACEMENT
44.WARM UP ENGINE (w/ Air Conditioning System)
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFO-1234yf(R1234yf))>REPLACEMENT
45.INSPECT FOR REFRIGERANT LEAK (w/ Air Conditioning System)
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFO-1234yf(R1234yf))>REPLACEMENT
46.INSPECT FOR COOLANT LEAK
12611
47.INSTALL NO. 1 ENGINE COVER
51441
48.INSTALL NO. 1 ENGINE UNDER COVER
Install the No. 1 engine under cover with the 4 bolts, 2 screws and 10 clips.