Home › Vehicle Interior › INTERIOR PANELS / TRIM › LOWER INSTRUMENT PANEL › from 2016.08
RM3090E _58 Vehicle Interior _008791 INTERIOR PANELS / TRIM _0049315 LOWER INSTRUMENT PANEL A

INTERIOR PANELS / TRIM  LOWER INSTRUMENT PANEL  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.TABLE OF BOLT, SCREW AND NUT

HINT:

All bolts, screws and nuts relevant to installing and removing the instrument panel are shown along with their alphabet code in the table below.


B339755E01
5.354,0.052 6.76,0.26 1.406,0.208 10 mm (in.) (L = Length) 0.229,1.292 0.688,1.49 0.458,0.198 10 <A> 0.208,0.458 0.823,0.656 0.615,0.198 10 Code 3.625,0.458 4.396,0.656 0.771,0.198 10 Shape 2.583,0.458 3.198,0.656 0.615,0.198 10 Code 1.344,0.458 2.115,0.656 0.771,0.198 10 Shape 5.948,0.458 6.719,0.656 0.771,0.198 10 Shape 4.865,0.458 5.479,0.656 0.615,0.198 10 Code 2.615,1.292 3.073,1.49 0.458,0.198 10 <B> 4.896,1.292 5.354,1.49 0.458,0.198 10 <C> 0.24,2.198 0.698,2.396 0.458,0.198 10 <D> 2.615,3.156 3.073,3.354 0.458,0.198 10 <H> 2.615,2.198 3.073,2.396 0.458,0.198 10 <E> 0.229,3.156 0.688,3.354 0.458,0.198 10 <G> 4.917,2.198 5.375,2.396 0.458,0.198 10 <F> 2.104,0.969 2.417,1.167 0.313,0.198 10 φ5 1.969,2.99 3.042,3.188 1.073,0.198 10 (0.197) 1.99,1.406 2.906,1.604 0.917,0.198 10 L = 14 1.969,1.594 3.042,1.792 1.073,0.198 10 (0.551) 4.365,0.969 4.677,1.167 0.313,0.198 10 φ5 4.25,1.177 5.323,1.375 1.073,0.198 10 (0.197) 4.271,1.406 5.188,1.604 0.917,0.198 10 L = 18 4.25,1.594 5.323,1.792 1.073,0.198 10 (0.708) 6.656,0.969 6.969,1.167 0.313,0.198 10 φ6 6.531,1.177 7.01,1.365 0.479,0.188 10 (0.236) 6.563,1.406 6.979,1.583 0.417,0.177 10 L = 20 6.531,1.594 6.969,1.781 0.438,0.188 10 (0.787) 2.094,1.875 2.406,2.073 0.313,0.198 10 φ6 1.99,2.313 2.906,2.51 0.917,0.198 10 L = 16 1.969,2.083 2.448,2.271 0.479,0.188 10 (0.236) 1.969,2.521 2.448,2.708 0.479,0.188 10 (0.630) 4.365,1.875 4.677,2.073 0.313,0.198 10 φ6 2.104,2.792 2.417,2.99 0.313,0.198 10 φ5 1.969,1.177 3.042,1.375 1.073,0.198 10 (0.197) 2,3.219 2.917,3.417 0.917,0.198 10 L = 16 1.969,3.427 2.448,3.615 0.479,0.188 10 (0.630) 4.25,2.083 4.729,2.271 0.479,0.188 10 (0.236) 4.271,2.313 4.688,2.49 0.417,0.177 10 L = 20 4.25,2.531 4.688,2.719 0.438,0.188 10 (0.787) 4.365,2.792 4.677,2.99 0.313,0.198 10 φ6 6.656,1.875 6.969,2.073 0.313,0.198 10 φ7 6.563,2.313 6.979,2.49 0.417,0.177 10 L = 20 6.542,2.083 7.021,2.271 0.479,0.188 10 (0.275) 6.542,2.531 6.979,2.719 0.438,0.188 10 (0.787) 4.25,2.99 4.729,3.177 0.479,0.188 10 (0.236) 4.24,3.427 4.719,3.615 0.479,0.188 10 (0.866) 4.26,3.24 4.677,3.417 0.417,0.177 10 L = 22

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 58901A 5.REMOVE REAR CONSOLE BOX SUB-ASSEMBLY

Hide 55433B 6.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

a.
B337813

Detach the 8 clips and remove the lower No. 2 instrument panel finish panel.


b.
B337815C03
2.656,0.823 2.906,1.01 0.25,0.188 12 true *A 1.865,1.948 2.104,2.146 0.24,0.198 12 true *B 1.469,0.823 1.75,1.042 0.281,0.219 12 true *C 1.177,0.885 1.417,1.083 0.24,0.198 12 true *D 0.885,0.792 1.125,0.979 0.24,0.188 12 true *E 2.406,1.802 2.646,1.99 0.24,0.188 12 true *B
*A w/ Drive Mode Switch
*B w/ Seat Heater System
*C w/ PTC Heater
*D for Windshield Deicer
*E w/ USB Audio System


for LHD:

Disconnect each connector.


c.
B364998C02
0.656,1.76 0.906,1.958 0.25,0.198 12 true *A 1,0.74 1.26,0.948 0.26,0.208 12 true *B 1.583,1.802 1.823,2 0.24,0.198 12 true *C 2.458,1.792 2.708,1.99 0.25,0.198 12 true *D 1.969,1.833 2.229,2.031 0.26,0.198 12 true *C
*A w/ Drive Mode Switch
*B w/ Lane Departure Alert System
*C w/ Seat Heater System
*D w/ USB Audio System


for RHD:

Disconnect each connector.


Hide 55606 7.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B337814

Remove the 2 screws <A> or <B>.


b.

Detach the 2 claws and 2 guides and remove the No. 1 instrument panel under cover sub-assembly.


c.

w/ Foot Light:

Disconnect the connector.


d.

w/ Tire Pressure Warning System:

Disconnect the connector.


Hide 55545 8.REMOVE FUSE BOX OPENING COVER

a.
B337819C01
1.177,1.958 1.333,2.156 0.156,0.198 10 false .
V100155

Protective Tape


for LHD:

i.

Apply protective tape as shown in the illustration.


ii.

Detach the 8 clips and remove the fuse box opening cover.


iii.
B337821C04
1.583,0.563 2.135,0.792 0.552,0.229 12 true *A, *B 1.24,0.573 1.5,0.76 0.26,0.188 12 true *C 0.927,1.708 1.188,1.896 0.26,0.188 12 true *D
*A w/ Headlight Leveling
*B w/ Light Control Rheostat
*C w/ VSC OFF Switch
*D w/ Blind Spot Monitor


Disconnect each connector and detach the wire harness clamp.



b.
B337817C01
1.26,4.031 1.417,4.229 0.156,0.198 10 false .
V100155

Protective Tape


for RHD:

i.

Apply protective tape as shown in the illustration.


ii.

Detach the 9 clips and remove the fuse box opening cover.


iii.
B337822C03
1.875,1.281 2.104,1.49 0.229,0.208 12 true *B 2.354,1.323 2.625,1.531 0.271,0.208 12 true *A
*A w/ VSC OFF Switch
*B w/ Headlight Leveling


Disconnect each connector.



Hide 55432B 9.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for LHD without Driver Side Knee Airbag)

a.
B337824C01
2.146,2.552 2.302,2.75 0.156,0.198 10 false .
V100155

Protective Tape


Apply protective tape as shown in the illustration.


b.

Detach the 4 clips and 4 claws and remove the lower instrument panel finish panel.


Hide 73900 10.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55607 11.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B337823

Detach the 2 claws and 2 guides and remove the No. 2 instrument panel under cover sub-assembly.


b.

w/ Foot Light:

Disconnect the connector.


Hide 67914B 12.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 67913B 13.REMOVE FRONT DOOR SCUFF PLATE RH

Hide 62112 14.REMOVE COWL SIDE TRIM BOARD LH

a.
B337827

Remove the nut.


b.

Detach the clip and remove the cowl side trim board LH.


Hide 62111C 15.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 55950G 16.REMOVE DEFROSTER NOZZLE ASSEMBLY

a.
B337828

Disconnect the connector and detach the 2 wire harness clamps.


b.

Detach the 3 claws and remove the defroster nozzle assembly.


Hide 55870B 17.REMOVE HEATER TO REGISTER DUCT ASSEMBLY

a.
B337829

Remove the 2 clips.


b.

Pull up the heater to register duct assembly to detach the 6 claws and remove it.


Hide 18.REMOVE LOWER INSTRUMENT PANEL (for LHD)

a.

Disconnect each connector and detach each wire harness clamp.


b.

Detach the claw and disconnect the hood lock control lever.


c.

Detach the 2 claws and disconnect the DLC3.


d.

Detach the 2 claws and disconnect the cooler thermistor.

B451999C01
0.563,2.542 0.802,2.729 0.24,0.188 12 true *A 1.094,1.833 1.333,2.021 0.24,0.188 12 true *B 3.698,2.958 3.938,3.146 0.24,0.188 12 true *D 4.24,1.24 4.479,1.427 0.24,0.188 12 true *C
*A for 4WD/AWD *B w/ Power Back Door
*C w/ Downhill Assist Control *D w/ Entry and Start System



e.

Remove the 6 bolts <E> or <F> and 2 bolts <C> or <D>.


f.

Remove the bolt <G> and lower instrument panel.

B337832C02
1.167,1.021 1.479,1.219 0.313,0.198 10 *1 2.406,1.104 2.719,1.302 0.313,0.198 10 *1 4.76,1.073 5.073,1.271 0.313,0.198 10 *1 3.958,2.958 4.271,3.156 0.313,0.198 10 *1 5.885,0.958 6.198,1.156 0.313,0.198 10 *1 3.135,2.927 3.448,3.125 0.313,0.198 10 *1 5.385,1.688 5.698,1.885 0.313,0.198 10 *1 1.198,2.875 1.51,3.073 0.313,0.198 10 *2 5.885,2.833 6.198,3.031 0.313,0.198 10 *2 4.99,2.135 5.302,2.333 0.313,0.198 10 *3
*1 Bolt <E> or <F> *2 Bolt <C> or <D>
*3 Bolt <G> - -



Hide 19.REMOVE LOWER INSTRUMENT PANEL (for RHD)

a.

Disconnect each connector and detach each wire harness clamp.


b.

Detach the claw and disconnect the hood lock control lever.


c.

Detach the 2 claws and disconnect the DLC3.


d.

Detach the 2 claws and disconnect the cooler thermistor.

B452000C01
3.958,0.396 4.219,0.604 0.26,0.208 12 true *A 3.875,1.156 4.135,1.365 0.26,0.208 12 true *B 5.385,1.156 5.646,1.365 0.26,0.208 12 true *C 6.615,2.854 6.875,3.063 0.26,0.208 12 true *D 1.896,4.969 2.156,5.177 0.26,0.208 12 true *D
*A for 4WD/AWD *B w/ Power Back Door
*C w/ Downhill Assist Control *D w/ Entry and Start System



e.

Remove the 7 bolts <E> or <F> and 2 bolts <C> or <D>.


f.

Remove the bolt <G> and lower instrument panel.

B340247C01
2.208,1.083 2.521,1.281 0.313,0.198 10 *1 4.74,1.094 5.052,1.292 0.313,0.198 10 *1 6.021,0.958 6.333,1.156 0.313,0.198 10 *1 4.927,2.125 5.24,2.323 0.313,0.198 10 *1 2.948,2.938 3.26,3.135 0.313,0.198 10 *1 1.125,2.896 1.438,3.094 0.313,0.198 10 *2 4.188,2.896 4.5,3.094 0.313,0.198 10 *1 1.073,0.948 1.385,1.146 0.313,0.198 10 *1 6,2.885 6.313,3.083 0.313,0.198 10 *2 2.052,2.083 2.365,2.281 0.313,0.198 10 *3
*1 Bolt <E> or <F> *2 Bolt <C> or <D>
*3 Bolt <G> - -