Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › from 2015.10
RM3090E _58 Vehicle Interior _008791 INTERIOR PANELS / TRIM _0049317 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 64309A 3.REMOVE PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY (w/ Partition Net)

a.
B435736

Release the 4 locks and remove the package tray trim pocket sub-assembly.


Hide 64910N 4.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

a.
B435737

Release the 2 locks and remove the tonneau cover assembly.


Hide 58410B 5.REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire, for Compact Spare Tire)

a.
B435738

Remove the deck board assembly.


Hide 58410B 6.REMOVE DECK BOARD ASSEMBLY (for Full Size Spare Tire)

a.
B435739

Remove the deck board assembly.


Hide 64997 7.REMOVE DECK FLOOR BOX LH

B423641

a.

Using a clip remover, remove the 2 clips.


b.

Detach the 4 claws and remove the deck floor box LH.


Hide 58417H 8.REMOVE REAR NO. 3 FLOOR BOARD

a.

for Compact Spare Tire:

i.
B435735

Detach the 2 clips and 2 guides and remove the rear No. 3 floor board.



b.

for Full Size Spare Tire:

i.
B435734

Detach the 4 clips and remove the rear No. 3 floor board.



Hide 58416K 9.REMOVE REAR NO. 2 FLOOR BOARD

HINT:

Use the same procedure described for the rear No. 3 floor board side.


Hide 58386 10.REMOVE REAR FLOOR FINISH PLATE (w/o Spare Tire, for Compact Spare Tire)

B337886

a.

Detach the 2 claws, 4 clips and 2 guides and remove the rear floor finish plate.


Hide 64716P 11.REMOVE REAR DECK TRIM COVER (for Full Size Spare Tire)

a.
B435740

Detach the 3 claws and 4 clips and remove the rear deck trim cover.


Hide 58577E 12.REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (w/o Spare Tire, for Compact Spare Tire)

a.

Open the rear No. 1 floor board.


b.
B423642

Remove the 4 screws.


c.

Detach the 4 clips and remove the rear No. 1 floor mat support side plate together with the rear No. 1 floor board.


Hide 58577E 13.REMOVE REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE (for Full Size Spare Tire)

a.

Open the rear No. 1 floor board.


b.
B337889

Remove the 4 screws.


c.

Detach the 4 clips and remove the rear No. 1 floor mat support side plate together with the rear No. 1 floor board.


Hide 67914B 15.REMOVE FRONT DOOR SCUFF PLATE LH

a.
B337826

Detach the 8 claws and 2 clips and remove the front door inside scuff plate LH.


Hide 67913B 16.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 62312B 17.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B337906

Remove the front door opening trim weatherstrip LH.


Hide 62311B 18.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 67918E 19.REMOVE REAR DOOR SCUFF PLATE LH

a.
B337896

Detach the 2 claws and 6 clips and remove the rear door scuff plate LH.


Hide 67917C 20.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 62332C 21.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

B337907

a.

Remove the rear door opening trim weatherstrip LH.


Hide 62331C 22.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 64718A 23.REMOVE DECK TRIM SERVICE HOLE COVER

HINT:

Use the same procedure for both deck trim service hole covers.


a.
B435732C01
0.885,1.427 1.302,1.01 true 0.74,1.396 0.948,1.552 0.208,0.156 10 true *1
*1 Protective Tape


Using a screwdriver, detach the 4 claws and 2 guides and disconnect the deck trim service hole cover.


Hide 64740E 24.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

a.

Remove the screw and 2 bolts.


b.

Open the tether anchor set bracket cover.


c.

Remove the bolt and tether anchor set bracket.


d.

Remove the bolt and luggage hold belt striker assembly.


e.

Detach the 6 claws and 4 clips and remove the deck trim side panel assembly LH.


f.

Disconnect the connector.

B423643


Hide 64730J 25.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

a.

Remove the screw and 2 bolts.


b.

Open the tether anchor set bracket cover.


c.

Remove the bolt and tether anchor set bracket.


d.

Remove the bolt and luggage hold belt striker assembly.


e.

Detach the 6 claws and 4 clips and remove the deck trim side panel assembly RH.

B423644


Hide 73178A 26.REMOVE SEAT BELT ANCHOR COVER CAP

Hide 62480A 27.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY LH

a.
B337894

Remove the bolt and disconnect the rear seat outer belt shoulder anchor.


b.
B337895

Detach the 8 clips and remove the inner roof side garnish assembly LH.


Hide 62470A 28.REMOVE INNER ROOF SIDE GARNISH ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 73135A 29.REMOVE SHOULDER BELT ANCHOR COVER RH

Hide 73233 30.REMOVE OUTER LAP BELT ANCHOR COVER

Hide 62414A 31.REMOVE LOWER CENTER PILLAR GARNISH LH

a.
B337898

Remove the bolt and disconnect the front seat outer belt floor anchor.


b.
B337897

Detach the 2 clips and 2 claws and remove the lower center pillar garnish LH.


Hide 62413A 32.REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 62412 33.REMOVE CENTER PILLAR GARNISH LH

a.
B337899

Remove the 2 clips.


b.

Detach the clip and remove the center pillar garnish LH.


c.

Pass the front seat outer belt floor anchor through the hole of the center pillar garnish LH.


Hide 62411 34.REMOVE CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 62212 35.REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

a.
B337789

Pull the upper part of the front pillar garnish LH toward the inside of the cabin and detach the 2 clips.


b.

Detach the 3 guides and remove the front pillar garnish LH.


Hide 62211 36.REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

HINT:

Use the same procedure described for the LH side.


Hide 62212 37.REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

a.
B337791C01
1.906,0.354 2.198,0.354 2.198,0.354 2.385,0.74 false 1.74,0.271 2.052,0.469 0.313,0.198 10 *1
*1 Front Pillar Garnish Clip


Pull the upper part of the front pillar garnish LH toward the inside of the cabin and detach the 2 front pillar garnish clips.

HINT:

Make the front pillar garnish LH hang down from the front pillar garnish clip.



b.
B337793C01
2.365,0.417 2.469,0.219 2.469,0.219 2.656,0.219 false 2.677,0.146 2.99,0.344 0.313,0.198 10 *1
*1 Front Pillar Garnish Clip
V100155

Protective Tape


Turn the ends of the 2 front pillar garnish clips 90° with needle-nose pliers and disconnect them from the front pillar garnish LH.

HINT:

Tape the tips of the needle-nose pliers before use.



c.

Detach the 3 guides and remove the front pillar garnish LH.


d.
B422591N02
1.448,0.156 1.625,0.302 0.177,0.146 10 true A

While pulling the front pillar garnish clip in direction A with a finger, insert a screwdriver at the position shown in the illustration.


e.
B422592N02
0.844,0.167 1,0.344 0.156,0.177 10 true B

While pulling the front pillar garnish clip in direction B with a finger, insert a screwdriver at the position shown in the illustration to detach the front pillar garnish clip.

NOTICE:

If the front pillar garnish clip is damaged, replace it with a new one.



f.
B337795C01
1.365,2.188 1.615,2.188 1.615,2.188 1.875,1.979 true 1.854,2.969 2.188,2.969 2.188,2.969 2.427,2.688 true 1.198,2.083 1.51,2.281 0.313,0.198 10 false *1 1.698,2.854 2.01,3.052 0.313,0.198 10 false *2
*1 Curtain Shield Airbag Assembly LH
*2 Protective Cover
V100155

Adhesive Tape


Protect the curtain shield airbag assembly LH.

i.

Completely cover the curtain shield airbag assembly LH with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish assembly LH is removed.




Hide 62211 38.REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

HINT:

Use the same procedure described for the LH side.


Hide 74320 40.REMOVE VISOR ASSEMBLY LH

a.
B337900

Remove the 2 screws and visor assembly LH.


Hide 74310 41.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 74348 42.REMOVE VISOR HOLDER

HINT:

Use the same procedure for both visor holders.


a.
B337901

Turn the visor holder clockwise approximately 45° and pull it as shown in the illustration.


b.

Detach the 2 claws and remove the visor holder.


Hide 81260A 43.REMOVE MAP LIGHT ASSEMBLY

Hide 74610A 44.REMOVE ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for all assist grips.


a.
B337904C01
0.833,0.24 1.042,0.49 0.208,0.25 10 false .
V100155

Protective Tape


Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.



b.
B337905

Detach the 2 clips and remove the assist grip sub-assembly.


Hide 81240 45.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 87834 46.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 89943 47.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

Hide 86466E 48.REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

Hide 86466D 49.REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

Hide 63318C 50.REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

a.
B423645

Remove the sun roof opening trim moulding.


Hide 63310 51.REMOVE ROOF HEADLINING ASSEMBLY

a.
B439427

w/ EC Mirror:

Disconnect the connector.


b.
B439428

w/ Rain Sensor, w/o Pre-crash Safety System:

Disconnect the connector.


c.
B439429

w/ Rain Sensor, w/ Pre-crash Safety System:

Disconnect the connector.


d.
B439426

w/ Pre-crash Safety System:

Disconnect the connectors.


e.
B423646

w/ Sliding Roof:

Disconnect the connector.


f.
B337911

Disconnect the connector from the rear pillar RH.


g.
B337909

Disconnect the 2 connectors and detach the 3 clips and 3 wire harness clamps from the front pillar LH.


h.
B337910

Detach the 4 wire harness clamps from the front pillar RH.


i.

w/o Sliding Roof:

i.
B423647

Remove the 5 clips.


ii.

Remove the roof headlining assembly as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining assembly when taking it out.


B423649



j.

w/ Sliding Roof:

i.
B423648

Remove the 3 clips.


ii.

Remove the roof headlining assembly as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining assembly when taking it out.


B423650



Hide 66423A 52.REMOVE FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.
B337917

Detach the 4 clips and remove the front side rail spacer LH.


Hide 66413C 53.REMOVE FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

HINT:

Use the same procedure described for the LH side.


Hide 66424 54.REMOVE REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.
B337918

Detach the 4 clips and remove the rear side rail spacer LH.


Hide 66414A 55.REMOVE REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

HINT:

Use the same procedure described for the LH side.


Hide 66424 56.REMOVE REAR SIDE RAIL SPACER LH (w/ Curtain Shield Airbag)

HINT:

When removing or replacing the rear side rail spacer LH, be sure to remove the curtain shield airbag assembly LH.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CURTAIN SHIELD AIRBAG ASSEMBLY>REMOVAL


a.
B337926

Remove the bolt.


b.

Detach the clip and remove the rear side rail spacer LH.


Hide 66414A 57.REMOVE REAR SIDE RAIL SPACER RH (w/ Curtain Shield Airbag)

HINT:

Use the same procedure described for the LH side.


Hide 66425B 58.REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.
B337919

Detach the 3 clips and remove the No. 2 rear side rail spacer LH.


Hide 66415B 59.REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

HINT:

Use the same procedure described for the LH side.


Hide 66425B 60.REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/ Curtain Shield Airbag)

B337920C01
1.99,3.76 2.208,3.76 false 2.104,2.99 2.323,2.99 false 1.948,2.917 2.26,3.115 0.313,0.198 10 *1 1.823,3.688 2.135,3.885 0.313,0.198 10 *2
*1 Pin
*2 Clip


a.

Using needle-nose pliers, release the lock by pinching the 2 locks of the pin, and pull out the pin from the clip.


b.
B337922

Using 2 screwdrivers, detach the 2 claws by inserting the screwdrivers into the grooves of the clip as shown in the illustration, and then remove the clip from the vehicle body and disconnect the rear part of the curtain shield airbag assembly LH.


c.
B337925

Detach the wire harness clamp.


d.

Detach the 2 clips and remove the rear No. 2 side rail spacer LH.


Hide 66415B 61.REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/ Curtain Shield Airbag)

HINT:

Use the same procedure described for the LH side.