Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) › from 2016.08
RM3090E _57 Power Source / Network _008434 NETWORKING _0221950 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Check Bus 3 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the bus 3 CAN main wires and/or CAN branch wires when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU is below 54 Ω.

Detection Item Trouble Area

*1: w/ Audio and Visual System (for Radio and Display Type)

*2: w/ Telematics Transceiver

Resistance between terminals 6 (CA3H) and 21 (CA3L) of central gateway ECU is below 54 Ω.
·

Short in bus 3 CAN main wires

·

Short in bus 3 CAN branch wires

·

Central gateway ECU

·

Radio and display receiver assembly*1

·

Telematics transceiver*2

·

No. 8 CAN junction connector

·

No. 13 CAN junction connector*2



WIRING DIAGRAM

w/o Telematics Transceiver:
C334603E04
6.083,0.698 6.563,0.885 0.479,0.188 10 false CA3H 6.115,1.427 6.594,1.615 0.479,0.188 10 false CA3L 6.115,4.365 6.594,4.552 0.479,0.188 10 false CAYH 6.115,5.146 6.594,5.333 0.479,0.188 10 false CAYL 5.823,0.688 5.979,0.885 0.156,0.198 10 false 6 5.76,1.135 5.99,1.375 0.229,0.24 10 false 21 5.771,4.354 6,4.594 0.229,0.24 10 false 19 5.771,4.833 6,5.073 0.229,0.24 10 false 20 4.5,0.677 4.656,0.875 0.156,0.198 10 false 3 4.49,1.125 4.719,1.365 0.229,0.24 10 false 14 4.521,4.396 4.677,4.594 0.156,0.198 10 false 4 4.49,4.823 4.719,5.063 0.229,0.24 10 false 15 3.052,1.479 3.208,1.677 0.156,0.198 10 false 1 2.99,1.99 3.219,2.229 0.229,0.24 10 false 12 1.719,1.49 1.875,1.688 0.156,0.198 10 false 9 1.688,1.958 1.917,2.198 0.229,0.24 10 false 10 1.135,1.635 1.615,1.823 0.479,0.188 10 false CANH 1.156,2.167 1.635,2.354 0.479,0.188 10 false CANL 5.583,5.51 6.052,5.854 0.469,0.344 10 false G170 5.594,5.698 7.031,5.979 1.438,0.281 10 false Central Gateway ECU 2.823,5.719 4.823,5.99 2,0.271 10 false No. 8 CAN Junction Connector 2.813,5.531 3.313,5.844 0.5,0.313 10 false G173 0.104,2.594 1.573,2.906 1.469,0.313 10 false G143 0.104,2.771 2.771,3.167 2.667,0.396 10 false Radio and Display Receiver Assembly* 0.167,4.5 2.125,4.927 1.958,0.427 10 false *: w/ Audio and Visual System (for Radio and Display Type)

w/ Telematics Transceiver:
C348161E01
6.104,0.677 6.625,0.854 0.521,0.177 10 false CA3H 6.135,1.458 6.656,1.635 0.521,0.177 10 false CA3L 5.823,0.719 6.042,0.875 0.219,0.156 10 false 6 5.76,1.188 5.979,1.344 0.219,0.156 10 false 21 4.51,0.729 4.729,0.885 0.219,0.156 10 false 3 4.469,1.188 4.688,1.344 0.219,0.156 10 false 14 3.083,0.729 3.302,0.885 0.219,0.156 10 false 1 3.01,1.177 3.229,1.333 0.219,0.156 10 false 12 1.719,0.698 1.938,0.854 0.219,0.156 10 false 9 1.688,1.167 1.906,1.323 0.219,0.156 10 false 10 1.146,0.844 1.667,1.021 0.521,0.177 10 false CANH 1.146,1.292 1.667,1.469 0.521,0.177 10 false CANL 0.042,1.719 2.667,1.917 2.625,0.198 10 false G143 0.052,1.896 2.677,2.094 2.625,0.198 10 false Radio and Display Receiver Assembly* 2.844,2.469 4.833,2.667 1.99,0.198 10 false G173 2.844,2.635 4.833,2.833 1.99,0.198 10 false No. 8 CAN Junction Connector 2.844,5.667 4.969,5.865 2.125,0.198 10 false M39 2.854,5.833 4.979,6.031 2.125,0.198 10 false No. 13 CAN Junction Connector 6.094,4.375 6.615,4.552 0.521,0.177 10 false CAYH 6.115,5.115 6.635,5.292 0.521,0.177 10 false CAYL 5.75,4.406 5.969,4.563 0.219,0.156 10 false 19 5.76,4.875 5.979,5.031 0.219,0.156 10 false 20 4.5,1.667 4.719,1.823 0.219,0.156 10 false 2 4.479,2.01 4.698,2.167 0.219,0.156 10 false 13 4.49,3.854 4.708,4.01 0.219,0.156 10 false 3 4.469,4.125 4.688,4.281 0.219,0.156 10 false 14 4.5,4.406 4.719,4.563 0.219,0.156 10 false 2 4.469,4.865 4.688,5.021 0.219,0.156 10 false 13 3.083,4.396 3.302,4.552 0.219,0.156 10 false 1 3.021,4.875 3.24,5.031 0.219,0.156 10 false 12 1.708,4.385 1.927,4.542 0.219,0.156 10 false 15 1.719,4.865 1.938,5.021 0.219,0.156 10 false 16 1.167,4.531 1.688,4.708 0.521,0.177 10 false CANP 1.167,5.01 1.688,5.188 0.521,0.177 10 false CANN 0.427,5.458 2.104,5.667 1.677,0.208 10 false M38 0.427,5.635 2.104,5.844 1.677,0.208 10 false Telematics Transceiver 5.688,5.646 7.156,5.844 1.469,0.198 10 false G170 5.688,5.813 7.156,6.01 1.469,0.198 10 false Central Gateway ECU 0.188,7.135 4.146,7.375 3.958,0.24 10 false *: w/ Audio and Visual System (for Radio and Display Type)

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/o Telematics Transceiver A
w/ Telematics Transceiver B



A

2.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 CAN JUNCTION CONNECTOR)

B

6.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.

C311975C70
1.313,1.781 1.823,2.052 0.51,0.271 2.073,3.073 2.375,3.073 2.375,3.073 3.042,2.188 true 2.01,0.917 2.313,0.917 2.313,0.917 3.01,1.927 true 2.146,0.656 2.448,0.656 2.448,0.656 3.198,1.958 true 2.281,3.375 2.583,3.375 2.583,3.375 3.229,2.188 true 1.781,1.208 2.083,1.208 2.083,1.208 2.677,1.969 true 1.865,2.75 2.167,2.75 2.167,2.75 2.708,2.156 true 1.385,1.833 2.083,2.167 0.698,0.333 10 false G173 0.219,0.146 0.531,0.344 0.313,0.198 10 false *a 1.469,0.833 2.01,1.042 0.542,0.208 10 false CANH*c 1.531,2.99 2.063,3.25 0.531,0.26 10 false CANL*c 1.219,1.135 1.781,1.365 0.563,0.229 10 false CANH*b 1.333,2.667 1.865,2.875 0.531,0.208 10 false CANL*b 1.74,3.292 2.271,3.552 0.531,0.26 10 false CANL*c 1.583,0.573 2.125,0.781 0.542,0.208 10 false CANH*c
*a Front view of wire harness connector
(to No. 8 CAN Junction Connector)
*b to Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type])
*c to Central Gateway ECU - -



b.

Disconnect the No. 8 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*: w/ Audio and Visual System (for Radio and Display Type)

G173-1 (CANH) - G173-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Radio and display receiver assembly*
G173-3 (CANH) - G173-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU
G173-4 (CANH) - G173-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU



Result:
Proceed to
OK A
NG (Central gateway ECU CAN main wire) B
NG (ECU or sensor CAN branch wires) C



A

REPLACE NO. 8 CAN JUNCTION CONNECTOR

B

3.CONNECT CONNECTOR

C

5.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
3.CONNECT CONNECTOR
a.

Reconnect the G173 No. 8 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU)
4.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU)
a.
C326490C27
1.5,0.167 2.031,0.385 0.531,0.219 2.771,1.917 2.573,1.917 2.573,1.917 2.188,1.208 true 2.729,0.281 2.542,0.281 2.542,0.281 2.313,0.948 true 1.458,1.813 1.656,1.813 1.656,1.813 1.896,1.198 true 1.625,2.042 1.823,2.042 1.823,2.042 2.052,1.208 true 0.135,0.094 0.438,0.427 0.302,0.333 10 false *a 1.583,0.198 2.188,0.5 0.604,0.302 10 false G170 2.802,0.229 3.229,0.531 0.427,0.302 10 false CA3H 2.823,1.844 3.313,2.083 0.49,0.24 10 false CA3L 1.031,1.729 1.469,1.896 0.438,0.167 10 false CAYH 1.198,1.969 1.635,2.135 0.438,0.167 10 false CAYL
*a Front view of wire harness connector
(to Central Gateway ECU)


Disconnect the central gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-6 (CA3H) - G170-21 (CA3L) Cable disconnected from negative (-) battery terminal 200 Ω or higher
G170-19 (CAYH) - G170-20 (CAYL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 8 CAN JUNCTION CONNECTOR)

5.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
a.
C334654C01
1.469,0.26 1.969,0.51 0.5,0.25 1.406,0.99 0.917,0.417 0.917,0.417 0.75,0.417 true 2.406,1.844 2.24,1.844 2.24,1.844 1.417,1.104 true 0.104,0.083 0.458,0.396 0.354,0.313 10 false *a 1.552,0.281 2.031,0.594 0.479,0.313 10 false G170 0.333,0.313 0.917,0.542 0.583,0.229 10 false CA3H 2.458,1.75 3.042,1.979 0.583,0.229 10 false CA3L
*a Component with harness connected
(Central Gateway ECU)


Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited CAN branch wire is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-6 (CA3H) - G170-21 (CA3L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRES OR CONNECTOR

6.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.

C348123C03
1.75,1.896 2.24,2.156 0.49,0.26 2.854,1.958 2.406,1.042 2.406,1.042 2.25,1.042 true 3.042,1.969 2.542,0.813 2.542,0.813 2.385,0.813 true 2.854,2.177 2.479,2.927 2.479,2.927 2.323,2.927 true 3.052,2.167 2.646,3.208 2.646,3.208 2.49,3.208 true 2.677,1.979 2.26,1.344 2.26,1.344 2.104,1.344 true 2.708,2.177 2.354,2.646 2.354,2.646 2.198,2.646 true 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 1.552,1.25 2.198,1.438 0.646,0.188 10 false CANH*b 1.708,0.948 2.354,1.135 0.646,0.188 10 false CANH*c 1.646,2.563 2.292,2.75 0.646,0.188 10 false CANL*b 1.792,2.833 2.438,3.021 0.646,0.188 10 false CANL*c 1.823,1.948 2.469,2.135 0.646,0.188 10 false G173 1.802,0.719 2.448,0.906 0.646,0.188 10 false CANH*d 1.958,3.125 2.604,3.313 0.646,0.188 10 false CANL*d
*a Front view of wire harness connector
(to No. 8 CAN Junction Connector)
*b to Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type])
*c to No. 13 CAN Junction Connector *d to Central Gateway ECU



b.

Disconnect the No. 8 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to

*: w/ Audio and Visual System (for Radio and Display Type)

G173-1 (CANH) - G173-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Radio and display receiver assembly*
G173-2 (CANH) - G173-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 13 CAN junction connector
G173-3 (CANH) - G173-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU



Result:
Result Proceed to
OK A
NG (No. 13 CAN junction connector CAN main wire) B
NG (Central gateway ECU CAN main wire) C
NG (ECU or sensor CAN branch wires) D



A

REPLACE NO. 8 CAN JUNCTION CONNECTOR

B

7.CONNECT CONNECTOR

C

11.CONNECT CONNECTOR

D

13.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
7.CONNECT CONNECTOR
a.

Reconnect the G173 No. 8 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 13 CAN JUNCTION CONNECTOR)
8.CHECK FOR SHORT IN CAN BUS WIRES (NO. 13 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 13 CAN junction connector.

C348123C04
1.75,1.896 2.24,2.156 0.49,0.26 2.854,1.958 2.406,1.042 2.406,1.042 2.25,1.042 true 3.042,1.969 2.542,0.813 2.542,0.813 2.385,0.813 true 2.854,2.177 2.479,2.927 2.479,2.927 2.323,2.927 true 3.052,2.167 2.646,3.208 2.646,3.208 2.49,3.208 true 2.677,1.979 2.24,1.292 2.24,1.292 2.083,1.292 true 2.688,2.167 2.333,2.667 2.333,2.667 2.177,2.667 true 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 1.552,1.198 2.198,1.385 0.646,0.188 10 false CANH*b 1.813,0.729 2.458,0.917 0.646,0.188 10 false CANH*d 1.646,2.563 2.292,2.75 0.646,0.188 10 false CANL*b 1.938,3.115 2.583,3.302 0.646,0.188 10 false CANL*d 1.833,1.938 2.479,2.125 0.646,0.188 10 false M39 1.708,0.948 2.354,1.135 0.646,0.188 10 false CANH*c 1.813,2.833 2.458,3.021 0.646,0.188 10 false CANL*c
*a Front view of wire harness connector
(to No. 13 CAN Junction Connector)
*b to Telematics Transceiver
*c to Central Gateway ECU *d to No. 8 CAN Junction Connector



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
M39-1 (CANH) - M39-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Telematics transceiver
M39-2 (CANH) - M39-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU
M39-3 (CANH) - M39-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 8 CAN junction connector



Result:
Result Proceed to
OK A
NG (No. 8 CAN junction connector CAN main wire) B
NG (Central gateway ECU CAN main wire) C
NG (ECU or sensor CAN branch wires) D



A

REPLACE NO. 13 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 13 CAN JUNCTION CONNECTOR - NO. 8 CAN JUNCTION CONNECTOR)

C

9.CONNECT CONNECTOR

D

13.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
9.CONNECT CONNECTOR
a.

Reconnect the M39 No. 13 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU)
10.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU)
a.
C348160C01
1.479,0.115 1.969,0.458 0.49,0.344 2.063,1.188 2.198,1.865 2.198,1.865 2.323,1.865 true 1.917,1.198 2.063,2.073 2.063,2.073 2.188,2.073 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 1.552,0.208 2.125,0.406 0.573,0.198 10 false G170 2.24,2 2.813,2.156 0.573,0.156 10 false CAYH 2.375,1.771 2.948,1.969 0.573,0.198 10 false CAYL
*a Front view of wire harness connector
(to Central Gateway ECU)


Disconnect the central gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-19 (CAYH) - G170-20 (CAYL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 13 CAN JUNCTION CONNECTOR)

11.CONNECT CONNECTOR
a.

Reconnect the G173 No. 8 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU)
12.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU)
a.
C348160C02
1.479,0.115 1.969,0.458 0.49,0.344 2.302,0.948 2.521,0.333 2.521,0.333 2.646,0.333 true 2.188,1.188 2.51,1.906 2.51,1.906 2.635,1.906 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 1.552,0.208 2.125,0.406 0.573,0.198 10 false G170 2.74,0.24 3.313,0.396 0.573,0.156 10 false CA3H 2.708,1.833 3.281,2.031 0.573,0.198 10 false CA3L
*a Front view of wire harness connector
(to Central Gateway ECU)


Disconnect the central gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-6 (CA3H) - G170-21 (CA3L) Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU - NO. 8 CAN JUNCTION CONNECTOR)

13.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
a.
C334654C01
1.469,0.26 1.969,0.51 0.5,0.25 1.406,0.99 0.917,0.417 0.917,0.417 0.75,0.417 true 2.406,1.844 2.24,1.844 2.24,1.844 1.417,1.104 true 0.104,0.083 0.458,0.396 0.354,0.313 10 false *a 1.552,0.281 2.031,0.594 0.479,0.313 10 false G170 0.333,0.313 0.917,0.542 0.583,0.229 10 false CA3H 2.458,1.75 3.042,1.979 0.583,0.229 10 false CA3L
*a Component with harness connected
(Central Gateway ECU)


Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited CAN branch wire is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G170-6 (CA3H) - G170-21 (CA3L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRES OR CONNECTOR