Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › SFI SYSTEM › from 2016.08
RM3090E _51 Engine / Hybrid System _008381 3ZR-FAE ENGINE CONTROL _0048627 SFI SYSTEM C

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0337  Crankshaft Position Sensor "A" Circuit Low Input  P0338  Crankshaft Position Sensor "A" Circuit High Input  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a No. 1 crankshaft position sensor plate and Magneto-Resistive Element (MRE) type sensor. The No. 1 crankshaft position sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM uses the NE signal to detect the crankshaft position and engine speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit Either of the following conditions is met (1 trip detection logic):
·

No crankshaft position sensor signal to the ECM while cranking.

·

No crankshaft position sensor signal to the ECM while engine running.


*
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No. 1 crankshaft position sensor plate

·

ECM


Comes on DTC stored
P0337 Crankshaft Position Sensor "A" Circuit Low Input Output voltage of crankshaft position sensor is below 0.3 V for 0.43 seconds (1 trip detection logic).
*
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Comes on DTC stored
P0338 Crankshaft Position Sensor "A" Circuit High Input Output voltage of crankshaft position sensor is higher than 4.7 V for 0.43 seconds (1 trip detection logic).
*
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

ECM


Comes on DTC stored
P0339 Crankshaft Position Sensor "A" Circuit Intermittent Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed is 1000 rpm or more.
(b) Starter signal is off.
(c) 3 seconds or more have elapsed since the starter signal switched from on to off.
*
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No. 1 crankshaft position sensor plate

·

ECM


- DTC stored

*: When the engine is stopped and started automatically due to stop and start system control, the crankshaft position sensor does not monitor during the automatic cranking.

A200774E03
2.969,1.177 3.396,1.438 0.427,0.26 10 GND 0.083,0.073 0.698,0.292 0.615,0.219 10 2 V/DIV. 1.229,1.875 2.25,2.104 1.021,0.229 10 20 ms./DIV.

Reference: Inspection using an oscilloscope.

The correct waveform is as shown.

ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine


MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor.

When the sensor output voltage remains at below 0.3 V, or higher than 4.7 V, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

7.

Idle the engine for 20 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0335, P0337, P0338 or P0339.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A375247E02
4.531,0.625 5.146,0.823 0.615,0.198 10 false VCNE 4.542,1.156 5,1.354 0.458,0.198 10 false NE+ 4.552,1.688 5.01,1.885 0.458,0.198 10 false NE- 4.292,0.615 4.604,0.813 0.313,0.198 10 false 81 4.208,1.156 4.667,1.354 0.458,0.198 10 false 114 4.208,1.688 4.667,1.885 0.458,0.198 10 false 113 1.719,0.615 2.031,0.813 0.313,0.198 10 false VC 1.635,1.156 2.094,1.354 0.458,0.198 10 false NE+ 1.667,1.698 2.125,1.896 0.458,0.198 10 false NE- 4.521,2.417 4.979,2.615 0.458,0.198 10 false B93 4.813,2.417 5.271,2.615 0.458,0.198 10 false ECM 1.417,2.281 2.188,2.479 0.771,0.198 10 false B88*2 0.75,2.281 1.979,2.479 1.229,0.198 10 false B106*1 0.729,2.479 4.708,2.677 3.979,0.198 10 false Crankshaft Position Sensor 3.313,2.938 7.073,3.177 3.76,0.24 10 false *1: for Manual Transaxle Models 3.354,3.333 4.604,3.531 1.25,0.198 10 false *2: for CVT Models 1.99,0.604 2.146,0.802 0.156,0.198 10 false 1 2.01,1.156 2.167,1.354 0.156,0.198 10 false 3 2.01,1.708 2.167,1.906 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:

1.

Connect the GTS to the DLC3.

2.

Start the engine.

3.

Turn the GTS on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

e.

Start the engine.


f.

Read the values displayed on the GTS while the engine is running.

Standard:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the GTS.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the GTS remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.




Result:
Proceed to
OK
NG



OK

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)
a.
A209301C70
0.042,0.542 0.448,0.844 0.406,0.302 0.042,0.958 0.448,1.292 0.406,0.333 1.052,1.792 1.406,1.271 true 0.823,1.823 1.26,2.083 0.438,0.26 10 false VC 0.094,0.146 0.531,0.406 0.438,0.26 10 false *a 0.125,1.021 0.563,1.281 0.438,0.26 10 false B88 0.083,0.583 0.698,0.781 0.615,0.198 10 false B106 0.49,0.573 1.104,0.771 0.615,0.198 10 false *A 0.5,1.031 0.813,1.229 0.313,0.198 10 false *B
*A for Manual Transaxle Models
*B for CVT Models
*a Front view of wire harness connector
(to Crankshaft Position Sensor)


Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Manual Transaxle Models
Tester Connection Condition Specified Condition
B106-1 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V

for CVT Models
Tester Connection Condition Specified Condition
B88-1 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transaxle Models
Tester Connection Condition Specified Condition
B106-3 (NE+) - B93-114 (NE+) Always Below 1 Ω
B106-2 (NE-) - B93-113 (NE-) Always Below 1 Ω
B106-3 (NE+) or B93-114 (NE+) - Body ground and other terminals Always 10 kΩ or higher
B106-2 (NE-) or B93-113 (NE-) - Body ground and other terminals Always 10 kΩ or higher

for CVT Models
Tester Connection Condition Specified Condition
B88-3 (NE+) - B93-114 (NE+) Always Below 1 Ω
B88-2 (NE-) - B93-113 (NE-) Always Below 1 Ω
B88-3 (NE+) or B93-114 (NE+) - Body ground and other terminals Always 10 kΩ or higher
B88-2 (NE-) or B93-113 (NE-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.
B319222C07
2.208,1.583 2.5,1.844 0.292,0.26 10 false *a 0.469,1.781 0.781,1.979 0.313,0.198 10 false OK 2.667,1.781 2.979,1.979 0.313,0.198 10 false NG
*a Clearance


Check the crankshaft position sensor installation condition.

OK:

Crankshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 1 CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

5.INSPECT NO. 1 CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
a.

Inspect the teeth of the No. 1 crankshaft position sensor plate.

OK:

No. 1 crankshaft position sensor plate does not have any cranks or deformation.



Result:
Proceed to
OK
NG



OK

6.REPLACE CRANKSHAFT POSITION SENSOR

NG

REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

6.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335, P0337, P0338 AND/OR P0339)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335, P0337, P0338 AND/OR P0339)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC is not output A
DTC P0335, P0337, P0338 and/or P0339 is output B



A

END

B

8.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transaxle Models
Tester Connection Condition Specified Condition
B106-1 (VC) - B93-81 (VCNE) Always Below 1 Ω
B106-1 (VC) or B93-81 (VCNE) - Body ground and other terminals Always 10 kΩ or higher

for CVT Models
Tester Connection Condition Specified Condition
B88-1 (VC) - B93-81 (VCNE) Always Below 1 Ω
B88-1 (VC) or B93-81 (VCNE) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR