Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › from 2016.08
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048163 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Entry Unlock and Unlatch Functions do not Operate Using Kick Sensor  


DESCRIPTION

If the touchless power back door function does not operate, it could indicate the certification ECU (smart key ECU assembly) did not transmit a power back door open request signal, or a malfunction in the power back door system.

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CUSTOMIZE SETTING (KICK SENSOR FUNCTION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Customize Setting / PSD & PBD operation.

PSD & PBD operation
Tester Display Description Default Setting ECU
Kick Sensor Function Function that enables/disables the touchless power back door. ON 0:OFF,1:ON Multiplex network door ECU
50006 21

Result:
Result Proceed to
The customize setting is "ON" A
The customize setting is "OFF" B



A

2.CHECK OPERATION HISTORY

B

2.CHECK OPERATION HISTORY
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Utility / Operation History.

Body Electrical > Entry&Start > Utility
Tester Display
Operation History
50005 125 52
Auto Entry Wireless Operation History
Parameter Name Content
Kick Sensor Open Request Signal. The multiplex network door ECU receives kick detection signals from the kick door control sensor and sends certification requests to the certification ECU (smart key ECU assembly). If certification is OK, an open permission is sent to the multiplex network door ECU.


Result:
Result Proceed to
Not output A
"Kick Sensor Open Request Signal" is output B



A

3.CHECK ENTRY LOCK OPERATION

B

GO TO POWER BACK DOOR SYSTEM (Power Back Door cannot be Operated Using Kick Sensor)

3.CHECK ENTRY LOCK OPERATION
a.

While carrying the electrical key transmitter sub-assembly, check that the entry unlock function operates when the back door opener switch is operated.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK


Result:
Result Proceed to
Smart lock/smart unlock function does not operate A
Smart lock/smart unlock function operates B



A

GO TO ENTRY AND START SYSTEM (Back Door Entry Lock and Unlock Functions do not Operate)

B

GO TO POWER BACK DOOR SYSTEM (Power Back Door cannot be Operated Using Kick Sensor)