Use the following procedure to troubleshoot the tire pressure warning system.
Make sure that the wireless door lock control system has exited diagnostic mode before performing the following procedure.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
Interview the customer to confirm the trouble.
It is important to collect as much specific information as possible from the customer to allow for a quick repair.
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
| Tester Display |
|---|
| ID 1 Tire Inflation Pressure |
| ID 2 Tire Inflation Pressure |
| ID 3 Tire Inflation Pressure |
| ID 4 Tire Inflation Pressure |
| ID 5 Tire Inflation Pressure |
Set the air pressure of all tires to the specified value(s).
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
Make sure the tires are cooled down when adjusting the tire pressure.
Display "ID Tire Inflation Pressure" in the Data List and check that the tire pressure data matches the adjusted pressure amount.
It takes a few minutes to display the updated tire pressure data.
Perform initialization.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
for ECE-R64 Type:
The warning threshold value changes depending on the driving conditions during initialization. As a result, the tire pressure warning light may not turn off even if the tire pressure is adjusted to the specified pressure.
| Proceed to |
|---|
| Tire pressure warning light remains on |
| Tire pressure warning light goes off |
Tire pressure warning light remains on
Tire pressure warning light goes off
Check the ECUs connected to the CAN bus.
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM
| Proceed to |
|---|
| No malfunction appears |
| Malfunction appears |
No malfunction appears
Malfunction appears
for LHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD with Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for LHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
for RHD without Central Gateway ECU: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC output |
| DTC is not output |
DTC output
DTC is not output
Refer to Diagnostic Trouble Code Chart.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
| Proceed to |
|---|
| NEXT |
NEXT
Refer to Problem Symptoms Table.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>PROBLEM SYMPTOMS TABLE
| Proceed to |
|---|
| NEXT |
NEXT
Refer to Electronic Circuit Inspection Procedure.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace parts based on the diagnosis result.
| Proceed to |
|---|
| NEXT |
NEXT
Check the Data List to confirm that the tire inflation pressure has been received.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DATA LIST / ACTIVE TEST
Perform initialization.
Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION
Confirm that the initialization has been completed.
| Proceed to |
|---|
| NEXT |
NEXT