Home › Engine / Hybrid System › 2AR-FE LUBRICATION › OIL PUMP › from 2016.08
RM3090E _51 Engine / Hybrid System _008401 2AR-FE LUBRICATION _0046911 OIL PUMP A

2AR-FE LUBRICATION  OIL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

Do not remove the oil pump or oil pump relief valve from the timing chain cover sub-assembly.


PROCEDURE

Hide 2.DISCONNECT ENGINE WIRE

a.

Disconnect the connectors and clamps securing the engine wire from the engine.


Hide 11201 4.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A195876

Remove the 16 bolts, 3 seal washers, cylinder head cover sub-assembly and cylinder head cover gasket.


b.
A196857

Remove the 2 camshaft bearing cap oil hole gaskets from the No. 1 camshaft bearing cap.


c.

Remove the gasket from the No. 2 camshaft bearing cap.


Hide 11193 5.REMOVE SPARK PLUG TUBE GASKET

a.
A195877

Using a screwdriver, pry out the 4 spark plug tube gaskets.

NOTICE:

Be careful not to damage the cylinder head cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 11301K 6.REMOVE CRANKSHAFT POSITION SENSOR

Hide 12315A 8.REMOVE ENGINE MOUNTING BRACKET RH

a.
A195868

Remove the 4 bolts and engine mounting bracket RH.


Hide 16634D 9.REMOVE DUST COVER (w/ Cover)

Hide 16620 10.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11310 11.REMOVE TIMING CHAIN COVER ASSEMBLY

a.
A196847

Remove the 17 bolts and 2 nuts.


b.
A296895C01
0.302,0.958 0.469,0.958 0.469,0.958 0.969,0.667 true 2.615,0.625 2.938,0.24 2.938,0.24 3.094,0.24 true 2.542,3.771 2.938,4.208 2.938,4.208 3.094,4.208 true 0.323,3.74 0.969,3.74 true 3.146,0.146 3.333,0.323 0.188,0.177 10 false *1 0.104,0.875 0.292,1.052 0.188,0.177 10 false *1 0.104,3.646 0.292,3.823 0.188,0.177 10 false *1 3.146,4.125 3.333,4.302 0.188,0.177 10 false *1
*1 Protective Tape


Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head, camshaft housing, cylinder block and stiffening crankcase with a screwdriver as shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head, camshaft housing, cylinder block, stiffening crankcase and timing chain cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



c.
A196858

Remove the 2 oil pump gaskets from the stiffening crankcase.


d.

Remove the oil hole cover gasket from the stiffening crankcase.


Hide 11301C 12.REMOVE TIMING CHAIN COVER OIL SEAL

a.
A302704C01
0.938,0.313 1.156,0.313 1.156,0.313 1.469,0.792 true 2.146,1.031 2.583,1.458 2.583,1.458 2.771,1.458 true 0.729,0.229 0.927,0.406 0.198,0.177 10 false *1 2.813,1.365 3.01,1.542 0.198,0.177 10 false *2
*1 Protective Tape
*2 Wooden Block


Using a screwdriver and wooden block, pry out the oil seal.

NOTICE:

Do not damage the surface of the oil seal press fit hole.


HINT:

Tape the screwdriver tip before use.