Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › ENGINE UNIT › from 2016.08
RM3090E _51 Engine / Hybrid System _008396 2AR-FE ENGINE MECHANICAL _0046880 ENGINE UNIT A

2AR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE ENGINE COVER JOINT

a.
A196900

Remove the 3 engine cover joints.


Hide 11101J 3.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side)

Hide 4.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 11102A 5.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 6.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 12108 7.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.

Remove the oil filler cap from the cylinder head cover sub-assembly.


b.

Remove the gasket from the oil filler cap.


Hide 11301K 8.REMOVE CRANKSHAFT POSITION SENSOR

Hide 12205 10.REMOVE PCV CASE

a.
A195869

Remove the 8 bolts and 2 nuts.


b.
A195878

Remove the PCV case by prying between the PCV case and cylinder block with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and PCV case.


HINT:

Tape the screwdriver tip before use.



Hide 12215 11.REMOVE SEPARATOR CASE

a.
A195870

Remove the 2 bolts, separator case and gasket.


Hide 16268 12.REMOVE NO. 1 WATER BY-PASS PIPE

a.
A194876

Remove the bolt, 2 nuts, water by-pass pipe and gasket.


Hide 16321 13.REMOVE WATER INLET

Hide 16331A 14.REMOVE THERMOSTAT

Hide 16634D 15.REMOVE DUST COVER (w/ Cover)

Hide 16620 16.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16100 17.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 15710 18.REMOVE OIL COOLER ASSEMBLY (w/ Oil Cooler)

Hide 16323 19.REMOVE WATER INLET HOUSING

a.
A195872

Remove the 4 bolts, nut, water inlet housing and gasket.


Hide 13471 20.REMOVE CRANKSHAFT PULLEY

a.
A297368C01
1.25,0.823 0.844,0.479 0.844,0.479 1.469,0.844 true 0.51,0.365 0.833,0.552 0.323,0.188 10 SST 0.854,1.677 1.052,1.865 0.198,0.188 10 *b 2.271,1.677 2.469,1.865 0.198,0.188 10 *a
*a Turn
*b Hold


Using SST, hold the crankshaft pulley and loosen the pulley bolt until 2 or 3 threads are screwed into the crankshaft.

SST
09213-54015  
09330-00021  

HINT:

Part number of installation bolt for SST (crankshaft pulley holdingtool): 91551-80650 (quantity: 2)



b.
A195874C07
2.333,0.25 2.479,0.25 2.479,0.25 2.563,0.677 false 1.469,1.188 1.469,1.021 1.469,1.021 1.844,0.833 true 0.969,1.698 1.104,1.698 1.104,1.698 1.365,2.385 false 1.354,1.208 1.75,1.396 0.396,0.188 10 false SST 2.115,0.156 2.354,0.333 0.24,0.177 10 false *1 0.615,1.604 0.938,1.792 0.323,0.188 10 false SST
*1 Pulley Bolt


Using SST and the pulley bolt, remove the crankshaft pulley.

SST
09950-50013  (09954-05011, 09951-05010, 09952-05010, 09953-05020)

HINT:

Apply lubricant to the threads and end of SST.



Hide 11201 21.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11193 22.REMOVE SPARK PLUG TUBE GASKET

Hide 12315A 23.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11310 24.REMOVE TIMING CHAIN COVER ASSEMBLY

Hide 25.REMOVE TIMING CHAIN COVER TIGHT PLUG

a.
A196859

Using a 14 mm hexagon wrench, remove the plug and gasket.


Hide 11324 26.REMOVE TIMING CHAIN COVER PLATE

Hide 11301C 27.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 28.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 13540 30.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 31.REMOVE CHAIN TENSIONER SLIPPER

Hide 13506 32.REMOVE CHAIN SUB-ASSEMBLY

Hide 13561 33.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13521 34.REMOVE CRANKSHAFT TIMING SPROCKET

a.
A196881

Remove the crankshaft timing sprocket from the crankshaft.


Hide 13050 35.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 36.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11103 37.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 15678A 39.REMOVE OIL CONTROL VALVE FILTER

a.
A196915

Remove the oil control valve filter from the No. 1 camshaft bearing cap.


Hide 11811 41.REMOVE NO. 1 CAMSHAFT BEARING

a.
A196916

Remove the No. 1 camshaft bearing.


Hide 11821 42.REMOVE NO. 2 CAMSHAFT BEARING

a.
A196917

Remove the No. 2 camshaft bearing.


Hide 43.REMOVE CAMSHAFT HOUSING STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


Hide 11151A 44.REMOVE CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


Hide 11114A 45.REMOVE CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pin unless it is being replaced.


Hide 13801 46.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 47.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 49.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11445 51.REMOVE CYLINDER BLOCK WATER JACKET SPACER

a.
A196938

Remove the cylinder block water jacket spacer from the cylinder block.

NOTICE:

Be sure to remove the water jacket spacer. If it is not removed, it may fall and become damaged when the cylinder block is inverted.



Hide 12101 53.REMOVE OIL PAN SUB-ASSEMBLY

a.
A196918

Remove the 11 bolts and 2 nuts.


b.
A118769

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and stiffening crankcase assembly, cut off the applied sealer and remove the oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the contact surfaces of the stiffening crankcase assembly and oil pan sub-assembly.

·

Be careful not to damage the stiffening crankcase flange.




Hide 15104 54.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A196919

Remove the 3 bolts, oil strainer sub-assembly and gasket.


Hide 12121 55.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A196920

Remove the 5 bolts and No. 1 oil pan baffle plate.


Hide 13411 56.INSPECT CRANKSHAFT BACKLASH

a.
A196931

Using a dial indicator, measure the backlash of the crankshaft and balance shaft as shown in the illustration.

Standard backlash:

0.05 to 0.20 mm (0.00197 to 0.00787 in.)


Maximum backlash:

0.20 mm (0.00787 in.)


If the backlash is more than the maximum, replace the engine balancer assembly.


Hide 13620B 57.REMOVE ENGINE BALANCER ASSEMBLY

a.
A196921

Remove the 7 bolts and engine balancer assembly.

NOTICE:

Do not disassemble the engine balancer assembly.



Hide 58.INSPECT BALANCE SHAFT THRUST CLEARANCE

Hide 11420 59.REMOVE STIFFENING CRANKCASE ASSEMBLY

a.
A196933

Remove the 7 bolts.


b.
A196934C06
0.052,0.052 0.302,0.25 0.25,0.198 10 *a 0.052,2.135 0.281,2.313 0.229,0.177 10 *b
*a LH Side
*b RH Side


Using a screwdriver, remove the stiffening crankcase by prying between the stiffening crankcase and cylinder block at the places shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and stiffening crankcase.


HINT:

Tape the screwdriver tip before use.



Hide 60.REMOVE STIFFENING CRANKCASE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


Hide 61.REMOVE STIFFENING CRANKCASE RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


Hide 11401L 62.REMOVE REAR ENGINE OIL SEAL

a.
A196937

Remove the rear engine oil seal from the cylinder block.