Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.08
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1380  Stop Light Control Relay Malfunction  


DESCRIPTION

Upon receiving the downhill assist control*1 or trailer sway control*2 operating signal from the skid control ECU (brake actuator assembly), the relay contact turns on and the stop light comes on.

*1: w/ Downhill Assist Control

*2: w/ Trailer Sway Control


DTC No. Detection Item DTC Detection Condition Trouble Area
C1380 Stop Light Control Relay Malfunction
·

When the voltage at terminal +BS is 9.5 V or higher, stop light drive output (STPO) is on and STP is OFF for 2 seconds or more.

·

When the voltage at terminal +BS is 9.5 V or higher, stop light drive output (STPO) is off and input signals for STP and STP2 differ for 5 seconds or more.


·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)

·

Stop light switch assembly



WIRING DIAGRAM

C345751E04
3.354,3.24 3.813,3.438 0.458,0.198 10 false OUT 5.5,1.948 5.729,2.167 0.229,0.219 10 false 5 3.521,2.135 3.656,2.427 0.135,0.292 10 false L 3.813,1.948 4.042,2.167 0.229,0.219 10 false 3 3.323,1.104 3.781,1.302 0.458,0.198 10 false ACC 3.833,3.063 4.063,3.281 0.229,0.219 10 false 1 2.031,1.51 2.167,1.802 0.135,0.292 10 false B 2.021,3.24 2.49,3.531 0.469,0.292 10 false GND 1.771,1.344 2,1.563 0.229,0.219 10 false 7 1.781,3.052 2.01,3.271 0.229,0.219 10 false 2 1.052,1.698 1.51,1.896 0.458,0.198 10 false STOP 5.771,1.125 6.229,1.323 0.458,0.198 10 false STPO 5.792,2.167 6.25,2.365 0.458,0.198 10 false STP2 5.792,3.271 6.25,3.469 0.458,0.198 10 false STP 5.448,0.958 5.677,1.177 0.229,0.219 10 false 26 3.833,0.948 4.063,1.167 0.229,0.219 10 false 4 5.458,3.073 5.688,3.292 0.229,0.219 10 false 35 1.906,0.271 3.292,0.448 1.385,0.177 10 false from Battery 5.552,3.958 7.104,4.375 1.552,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 5.188,3.958 5.563,4.208 0.375,0.25 10 false A100 1.885,3.885 4.01,4.177 2.125,0.292 10 false Stop Light Switch Assembly 4,4.323 5.385,4.5 1.385,0.177 10 false to Stop Light Circuit 1.51,3.885 1.823,4.135 0.313,0.25 10 false A77

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. On
Brake pedal released. Off



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

NG

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON


c.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
50003 105 37

d.

Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (STOP LIGHT CONTROL RELAY)

NG

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
3.PERFORM ACTIVE TEST USING GTS (STOP LIGHT CONTROL RELAY)
a.

Select the Active Test on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay Relay ON/OFF Stop lights come on
Vehicle condition: Vehicle stopped

b.

Perform the Active Test of the stop light control relay using the GTS.


c.

Select the Data List on the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light control relay (STPO terminal output) ON or OFF ON: Output on
OFF: Output off
-
Chassis > ABS/VSC/TRC > Active Test
Active Test Display
Stop Light Relay
Data List Display
Stop Light Relay Output
50004 105 5 291

d.

Check for stop light control relay operation using the Data List and stop light operation by performing the Active Test.


Result:
Result Proceed to
Data List content and stop light operation are normal. A
Data List content and stop light operation are abnormal or Data List content is normal but stop lights do not turn on or off. B



A

4.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)

B

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)
a.
C365682C09
1.5,0.135 1.958,0.344 0.458,0.208 1.042,0.271 1.229,0.271 1.229,0.271 1.417,0.885 true 0.094,0.042 0.406,0.24 0.313,0.198 10 false *a 1.563,0.156 1.979,0.354 0.417,0.198 10 false A100 0.635,0.177 1.083,0.375 0.448,0.198 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A100 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A100-5 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A100-5 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)

5.RECONFIRM DTC
a.

Reconnect the A100 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Proceed to
DTC C1380 is not output.
DTC C1380 is output.



DTC C1380 is not output.

DTC C1380 is output.

6.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Turn the ignition switch off.


b.

Check the stop light control relay.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION

OK:

The stop light control relay is normal.



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the A100 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A77 stop light switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A100-26 (STPO) -A77-4 (ACC) Always Below 1 Ω
A100-26 (STPO) or A77-4 (ACC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STPO CIRCUIT)

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C342353C82
1.49,0.104 1.865,0.375 0.375,0.271 2.646,1.813 2.646,1.625 2.646,1.625 2.198,1.323 true 0.104,0.104 0.417,0.26 0.313,0.156 10 false *a 1.521,0.156 1.979,0.354 0.458,0.198 10 false A100 2.531,1.844 2.906,2.031 0.375,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A100 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A100-35 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A100-35 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)