1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
51444
3.REMOVE REAR ENGINE UNDER COVER LH
for 2AD-FHV:
Click hereEngine / Hybrid System>2AD-FHV ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 2AD-FTV:
Click hereEngine / Hybrid System>2AD-FTV ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 2AR-FE:
Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 3ZR-FAE:
Click hereEngine / Hybrid System>3ZR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 3ZR-FE:
Click hereEngine / Hybrid System>3ZR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 2WW:
Click hereEngine / Hybrid System>2WW ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
4.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
for 2AD-FHV:
Click hereEngine / Hybrid System>2AD-FHV ENGINE CONTROL>ECM>REMOVAL
for 2AD-FTV:
Click hereEngine / Hybrid System>2AD-FTV ENGINE CONTROL>ECM>REMOVAL
for 2AR-FE:
Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FAE:
Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>ECM>REMOVAL
for 3ZR-FE:
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>ECM>REMOVAL
for 2WW:
Click hereEngine / Hybrid System>2WW ENGINE CONTROL>ECM>REMOVAL
55789D
5.INSTALL NO. 3 COWL TOP PANEL INSULATOR (for 2WW)
Remove the 4 nuts and No. 3 cowl top panel insulator.
17769
6.REMOVE AIR CLEANER SUPPORT
for 2AD-FHV:
Click hereEngine / Hybrid System>2AD-FHV ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 2AD-FTV:
Click hereEngine / Hybrid System>2AD-FTV ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
7.REMOVE FUEL FILTER ASSEMBLY
for 2AD-FHV:
Click hereEngine / Hybrid System>2AD-FHV ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 2AD-FTV:
Click hereEngine / Hybrid System>2AD-FTV ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 2WW:
Click hereEngine / Hybrid System>2WW FUEL>FUEL FILTER>REPLACEMENT
17119A
8.REMOVE AIR CLEANER BRACKET
for 2AD-FHV:
Click hereEngine / Hybrid System>2AD-FHV ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
for 2AD-FTV:
Click hereEngine / Hybrid System>2AD-FTV ENGINE MECHANICAL>ENGINE ASSEMBLY>REMOVAL
23921
9.REMOVE FUEL FILTER SUPPORT (for 2WW)
82121
10.DISCONNECT ENGINE WIRE
except 2WW:
Remove the bolt and detach the 2 clamps.
Remove the bolt and wire harness clamp bracket.
for CVT
Disconnect the connector.
Remove the bolt and disconnect the engine wire.
33820B
11.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)
Remove the nut and disconnect the transmission control cable assembly from the transmission control shaft lever.
Remove the clip and disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.
33823
12.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET (for Automatic Transmission)
Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle assembly.
Detach the clamp.
13.DRAIN BRAKE FLUID
Wash off brake fluid immediately if it comes in contact with any painted surface.
14.REMOVE BRAKE ACTUATOR ASSEMBLY
Release the lock lever and disconnect the connector from the brake actuator assembly.
Be careful not to allow brake fluid to enter the removed connector.
Disconnect the clamp from the brake actuator bracket assembly.
Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.
| *a | to Front Wheel Cylinder RH |
| *b | to Front Wheel Cylinder LH |
| *c | to Rear Wheel Cylinder RH |
| *d | to Rear Wheel Cylinder LH |
| *e | from Front Master Cylinder |
| *f | from Rear Master Cylinder |
Use tags or make a memo to identify the places to reconnect.
Remove the 4 bolts and brake actuator assembly from the brake actuator bracket assembly.
44590
15.REMOVE BRAKE ACTUATOR BRACKET ASSEMBLY
Remove the 3 nuts and brake actuator bracket assembly.
Be careful not to damage the brake tubes.
Disconnect the 3 clamps from the brake actuator bracket assembly.
16.REMOVE BRAKE ACTUATOR CASE COLLAR
Remove the 4 brake actuator case collars from the brake actuator bolt cushion.
44546A
17.REMOVE BRAKE ACTUATOR BOLT CUSHION
Remove the 4 brake actuator bolt cushions from the brake actuator bracket assembly.