1.DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFO-1234yf(R1234yf))>REPLACEMENT
2.REMOVE HEADLIGHT
for Halogen Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Halogen Headlight)>REMOVAL
for LED Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL
3. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
5.DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL
11212
6.REMOVE NO. 2 CYLINDER HEAD COVER
74404A
7.REMOVE BATTERY CLAMP SUB-ASSEMBLY
28800
8.REMOVE BATTERY
74431
9.REMOVE BATTERY TRAY
51441
10.REMOVE NO. 1 ENGINE UNDER COVER
52618
11.REMOVE FRONT LOWER BUMPER ABSORBER
Remove the 4 screws and front lower bumper absorber.
16683
12.REMOVE RADIATOR LOWER AIR GUIDE PLATE
Detach the 2 claws and remove the radiator lower air guide plate.
13.DRAIN ENGINE COOLANT
53629
14.REMOVE HOOD LOCK CONTROL CABLE COVER (w/ Cover)
53510
15.REMOVE HOOD LOCK ASSEMBLY
53630
16.DISCONNECT HOOD LOCK CONTROL CABLE ASSEMBLY
Detach the clamp to disconnect the hood lock control cable assembly.
52029
17.REMOVE FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY
Disconnect the horn connector.
Remove the 3 bolts and front bumper upper reinforcement sub-assembly.
16681
18.REMOVE RADIATOR UPPER AIR GUIDE PLATE
Remove the 6 clips and radiator upper air guide plate.
88703
19.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY
88706
20.DISCONNECT LIQUID PIPE SUB-ASSEMBLY
21.DISCONNECT WIRE HARNESS
| *a | w/o Hood Courtesy Switch |
Disconnect the 2 cooling fan motor connector.
Detach the 9 wire harness clamps.
16533B
22.REMOVE NO. 1 RADIATOR SUPPORT
Remove the 2 bolts and 2 No. 1 radiator supports.
53216A
23.REMOVE UPPER RADIATOR SUPPORT
Remove the 4 bolts and upper radiator support.
16057
24.DISCONNECT RADIATOR HOSE SUB-ASSEMBLY
Remove the 2 bolts.
Slide the hose clamp and disconnect the radiator hose sub-assembly from the No. 1 radiator hose.
16572D
25.DISCONNECT NO. 2 RADIATOR HOSE
Slide the hose clamp and disconnect the No. 2 radiator hose from the water inlet housing.
16261G
26.DISCONNECT NO. 1 WATER BY-PASS HOSE
Slide the hose clamp and disconnect the No. 1 water by-pass hose from the water by-pass pipe.
16264D
27.DISCONNECT NO. 2 WATER BY-PASS HOSE
Slide the hose clamp and disconnect the No. 2 water by-pass hose from the radiator assembly.
16400
28.REMOVE RADIATOR ASSEMBLY
Remove the radiator assembly together with the fan shroud.
After removing the radiator assembly, make sure that both lower radiator supports are attached to the fan shroud.
16057
29.REMOVE RADIATOR HOSE SUB-ASSEMBLY
Slide the 2 hose clamps and remove the radiator hose sub-assembly from the radiator assembly and water by-pass pipe.
16572D
30.REMOVE NO. 2 RADIATOR HOSE
Slide the hose clamp and remove the No. 2 radiator hose from the radiator assembly.
16268L
31.REMOVE WATER BY-PASS PIPE
Slide the hose clamp and disconnect the water by-pass hose from the radiator assembly.
Detach the 3 clamps to remove the water by-pass pipe.
16535
32.REMOVE RADIATOR LOWER SUPPORT
Remove the 2 radiator lower supports from the fan shroud.
16712
33.REMOVE NO. 2 FAN SHROUD
Remove the 2 bolts.
Detach the 2 claws and remove the No. 2 fan shroud.
88460
34.REMOVE COOLER CONDENSER ASSEMBLY
Detach the 2 guides and remove the condenser assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>CONDENSER(for 3ZR-FE, 3ZR-FAE, 2AR-FE)>REMOVAL
16711
35.REMOVE FAN SHROUD WITH COOLING FAN
Remove the 2 bolts and fan shroud.