Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for HV Model with Occupant Classification System)
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0369991 AIRBAG SYSTEM(for HV Model with Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for HV Model with Occupant Classification System)  B1660  P Seat Airbag Active Mode Indicator  


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the airbag sensor assembly and passenger airbag ON/OFF indicator.

The passenger airbag ON/OFF indicator indicates the operation condition of the instrument panel passenger without door airbag assembly.

DTC B1660 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1660 P Seat Airbag Active Mode Indicator One of the following conditions is met:
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the passenger airbag ON/OFF indicator circuit.

·

A passenger airbag ON/OFF indicator malfunction.

·

An airbag sensor assembly malfunction.


·

Instrument panel wire

·

Telltale light assembly (passenger airbag ON/OFF indicator)

·

Airbag sensor assembly


Comes on Not applicable

WIRING DIAGRAM

C411823E03
5.479,4.594 5.781,4.76 0.302,0.167 10 false G70 0.333,4.646 0.635,4.813 0.302,0.167 10 false G31 1.656,0.802 1.958,0.969 0.302,0.167 10 false 4 1.646,1.813 1.948,1.979 0.302,0.167 10 false 5 5.365,0.802 5.667,0.969 0.302,0.167 10 false 35 5.365,1.813 5.667,1.979 0.302,0.167 10 false 34 1.646,2.833 1.948,3 0.302,0.167 10 false 9 5.677,0.906 6.198,1.073 0.521,0.167 10 false PAON 5.677,1.896 6.052,2.063 0.375,0.167 10 false P-AB 5.365,2.792 5.667,2.958 0.302,0.167 10 false 33 5.365,3.802 5.667,3.969 0.302,0.167 10 false 32 5.677,2.896 6.198,3.063 0.521,0.167 10 false E1 5.677,3.927 6.052,4.094 0.375,0.167 10 false E2 1.115,0.906 1.563,1.073 0.448,0.167 10 false PAON 1.188,1.896 1.656,2.063 0.469,0.167 10 false P-AB 1.354,2.938 1.833,3.115 0.479,0.177 10 false IG 0.323,4.781 2.917,5.167 2.594,0.385 10 false Telltale Light Assembly (Passenger Airbag ON/OFF Indicator) 5.479,4.74 7.135,4.938 1.656,0.198 10 false Airbag Sensor Assembly 1.979,3.979 3.26,4.427 1.281,0.448 10 false from ECU-IG1 NO.4 Fuse

CAUTION / NOTICE / HINT

NOTICE:
·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Turn the power switch on (IG).


b.

Check the passenger airbag ON/OFF indicator operation.

HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>OPERATION CHECK



Result:
Result Proceed to
Passenger airbag ON/OFF indicator illumination is always on. A
Passenger airbag ON/OFF indicator illumination is always off. B



A

2.CHECK CONNECTION OF CONNECTORS

B

7.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and telltale light assembly.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

3.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.
C214663C10
0.521,1.49 0.719,1.656 0.198,0.167 10 false *1 2.51,1.604 2.708,1.771 0.198,0.167 10 false *2 1.51,1.229 1.708,1.396 0.198,0.167 10 false *3
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire


Disconnect the connectors from the airbag sensor assembly and telltale light assembly.


b.

Check that the connectors (on the airbag sensor assembly side and telltale light assembly side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

The connectors are deformed or damaged

REPLACE INSTRUMENT PANEL WIRE

4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.

Connect the connector to the telltale light assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


c.

Turn the power switch on (IG).


d.

Check the passenger airbag ON/OFF indicator operation.


Result:
Proceed to
The passenger airbag ON/OFF indicator does not come on
The passenger airbag ON/OFF indicator comes on



The passenger airbag ON/OFF indicator does not come on

5.CHECK DTC

The passenger airbag ON/OFF indicator comes on

6.CHECK INSTRUMENT PANEL WIRE
5.CHECK DTC
a.
C391328C05
1.01,1.26 1.323,1.458 0.313,0.198 10 false *1 1.823,1.375 2.135,1.573 0.313,0.198 10 false *2
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Connect the connectors to the airbag sensor assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

g.

Turn the power switch off.


h.

Turn the power switch on (IG), and wait for at least 60 seconds.


i.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1660 is not output
DTC B1660 is output


HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.




DTC B1660 is not output

DTC B1660 is output

6.CHECK INSTRUMENT PANEL WIRE
a.
C411483C01
0.302,1.198 0.719,1.448 0.417,0.25 1.25,3.75 1.667,4 0.417,0.25 1.833,0.927 2.177,0.771 2.177,0.771 2.323,0.771 true 1.656,1.052 2.156,1.313 2.156,1.313 2.281,1.313 true 2.448,4.042 2.75,3.333 2.75,3.333 2.917,3.333 false 2.521,4.031 2.792,3.792 2.792,3.792 2.885,3.792 false 2.625,4.313 2.802,4.438 2.802,4.438 2.927,4.438 false 2.385,0.698 2.844,0.896 0.458,0.198 10 false P-AB 2.344,1.229 2.802,1.427 0.458,0.198 10 false PAON 0.708,2.135 1.167,2.333 0.458,0.198 10 false D 1.021,2.125 1.479,2.323 0.458,0.198 10 false C 2.083,2.125 2.542,2.323 0.458,0.198 10 false B 2.396,2.125 2.854,2.323 0.458,0.198 10 false A 1.323,3.792 1.781,3.99 0.458,0.198 10 false G70 0.375,1.24 0.833,1.438 0.458,0.198 10 false G31 2.979,3.26 3.333,3.49 0.354,0.229 10 false P-AB 2.938,3.719 3.396,3.917 0.458,0.198 10 false PAON 0.406,2.656 0.719,2.813 0.313,0.156 10 false *1 2.865,2.719 3.177,2.875 0.313,0.156 10 false *2 1.552,2.344 1.865,2.5 0.313,0.156 10 false *3 3,4.365 3.313,4.521 0.313,0.156 10 false *4 0.344,0.313 0.656,0.469 0.313,0.156 10 false *a 1.26,3.208 1.573,3.365 0.313,0.156 10 false *b
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Telltale Light Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the telltale light assembly.


d.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


e.

Turn the power switch on (IG).


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G31-5 (P-AB) - Body ground Power switch on (IG) Below 1 V
G31-4 (PAON) - Body ground Power switch on (IG) Below 1 V



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


i.

Using a service wire, connect terminals 34 (P-AB) and 35 (PAON) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G31-5 (P-AB) - G31-4 (PAON) Always Below 1 Ω



k.

Disconnect the service wire from connector B.


l.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G31-5 (P-AB) - G31-4 (PAON) Always 1 MΩ or higher
G31-5 (P-AB) - Body ground Always 1 MΩ or higher
G31-4 (PAON) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK CONNECTION OF CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and telltale light assembly.


Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected



The connectors are properly connected

8.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

8.CHECK CONNECTORS
a.
C214663C11
0.521,1.49 0.719,1.656 0.198,0.167 10 false *1 2.51,1.604 2.708,1.771 0.198,0.167 10 false *2 1.51,1.229 1.708,1.396 0.198,0.167 10 false *3
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire


Disconnect the connectors from the airbag sensor assembly and telltale light assembly.


b.

Check that the connectors (on the airbag sensor assembly side and telltale light assembly side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

9.CHECK INSTRUMENT PANEL WIRE

The connectors are deformed or damaged

REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE
a.
C411483C03
0.302,1.198 0.719,1.448 0.417,0.25 1.25,3.75 1.667,4 0.417,0.25 1.833,0.938 2.177,0.771 2.177,0.771 2.323,0.771 true 1.677,1.052 2.167,1.25 2.167,1.25 2.313,1.25 true 2.448,4.042 2.75,3.333 2.75,3.333 2.917,3.333 false 2.521,4.031 2.792,3.792 2.792,3.792 2.885,3.792 false 2.625,4.313 2.802,4.438 2.802,4.438 2.927,4.438 false 2.385,0.698 2.844,0.896 0.458,0.198 10 false P-AB 2.365,1.177 2.823,1.375 0.458,0.198 10 false PAON 0.708,2.135 1.167,2.333 0.458,0.198 10 false D 1.031,2.135 1.49,2.333 0.458,0.198 10 false C 2.073,2.135 2.531,2.333 0.458,0.198 10 false B 2.396,2.125 2.854,2.323 0.458,0.198 10 false A 1.323,3.792 1.781,3.99 0.458,0.198 10 false G70 0.375,1.24 0.833,1.438 0.458,0.198 10 false G31 2.979,3.26 3.333,3.49 0.354,0.229 10 false P-AB 2.938,3.719 3.396,3.917 0.458,0.198 10 false PAON 0.406,2.656 0.719,2.813 0.313,0.156 10 false *1 2.865,2.719 3.177,2.875 0.313,0.156 10 false *2 1.552,2.344 1.865,2.5 0.313,0.156 10 false *3 3,4.365 3.313,4.521 0.313,0.156 10 false *4 0.344,0.313 0.656,0.469 0.313,0.156 10 false *a 1.26,3.208 1.573,3.365 0.313,0.156 10 false *b
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly
*3 Instrument Panel Wire
*4 Service Wire
*a Front view of wire harness connector
(to Telltale Light Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G31-5 (P-AB) - Body ground Power switch on (IG) Below 1 V
G31-4 (PAON) - Body ground Power switch on (IG) Below 1 V



d.

Turn the power switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 34 (P-AB) and 35 (PAON) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G31-5 (P-AB) - G31-4 (PAON) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G31-5 (P-AB) - G31-4 (PAON) Always 1 MΩ or higher
G31-5 (P-AB) - Body ground Always 1 MΩ or higher
G31-4 (PAON) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE)

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE)
a.
C411551C01
0.438,1.031 0.927,1.365 0.49,0.333 1.906,1.417 2.573,1.792 2.573,1.792 2.74,1.792 true 0.552,1.115 1.01,1.313 0.458,0.198 10 false G31 2.792,1.698 3.25,1.896 0.458,0.198 10 false IG 0.146,0.146 0.458,0.302 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Telltale Light Assembly)


Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G31-9 (IG) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
C411578C03
0.25,0.948 0.667,1.208 0.417,0.26 1.344,1.854 1.51,1.854 1.51,1.854 2,1.365 true 2.646,1.76 2.49,1.76 2.49,1.76 2.125,1.365 true 0.167,0.135 0.427,0.354 0.26,0.219 10 false *a 0.333,1 1.427,1.365 1.094,0.365 10 false G70 2.698,1.688 3.385,1.875 0.688,0.188 10 false PAON 0.938,1.792 1.625,1.979 0.688,0.188 10 false P-AB
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Connect the connector to the telltale light assembly.


d.

Using a service wire, connect terminal 35 (PAON) and body ground.


e.

Using a service wire, connect terminal 34 (P-AB) and body ground.


f.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


g.

Turn the power switch on (IG).


h.

Check the indicator according to the table below.

OK:
Tester Connection Switch Condition Passenger Airbag ON/OFF Indicator
G70-35 (PAON) - Body ground Power switch on (IG) "ON" comes on
G70-34 (P-AB) - Body ground Power switch on (IG) "OFF" comes on



i.

Turn the power switch off.


j.

Disconnect the service wire from airbag sensor assembly.


Result:
Proceed to
OK
NG



OK

12.CHECK DTC

NG

12.CHECK DTC
a.
C391328C05
1.01,1.26 1.323,1.458 0.313,0.198 10 false *1 1.823,1.375 2.135,1.573 0.313,0.198 10 false *2
*1 Telltale Light Assembly
*2 Airbag Sensor Assembly


Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


b.

Connect the connectors to the airbag sensor assembly.


c.

Connect the cable to the negative (-) auxiliary battery terminal and wait for at least 2 seconds.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTC B1660 is not output
DTC B1660 is output


HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.




DTC B1660 is not output

DTC B1660 is output