Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for HV Model with Occupant Classification System)
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0369991 AIRBAG SYSTEM(for HV Model with Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for HV Model with Occupant Classification System)  B1875  Short in Passenger Side Front Seat Cushion Squib Circuit  B1876  Open in Passenger Side Front Seat Cushion Squib Circuit  B1877  Short to GND in Passenger Side Front Seat Cushion Squib Circuit  B1878  Short to B+ in Passenger Side Front Seat Cushion Squib Circuit  


DESCRIPTION

The front seat cushion squib RH circuit consists of the airbag sensor assembly and the front seat cushion airbag assembly RH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the front seat cushion squib RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1875 Short in Passenger Side Front Seat Cushion Squib Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal 5 times in the front seat cushion squib RH circuit during primary check.

·

A front seat cushion airbag assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat cushion airbag assembly RH

·

Airbag sensor assembly


Comes on Comes on
B1876 Open in Passenger Side Front Seat Cushion Squib Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal in the front seat cushion squib RH circuit for 2 seconds.

·

A front seat cushion airbag assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat cushion airbag assembly RH

·

Airbag sensor assembly


Comes on Comes on
B1877 Short to GND in Passenger Side Front Seat Cushion Squib Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to ground signal in the front seat cushion squib RH circuit for 0.5 seconds.

·

A front seat cushion airbag assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat cushion airbag assembly RH

·

Airbag sensor assembly


Comes on Comes on
B1878 Short to B+ in Passenger Side Front Seat Cushion Squib Circuit
One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to B+ signal in the front seat cushion squib RH circuit for 0.5 seconds.

·

A front seat cushion airbag assembly RH malfunction.

·

An airbag sensor assembly malfunction.


·

Floor wire

·

Front seat cushion airbag assembly RH

·

Airbag sensor assembly


Comes on Comes on

WIRING DIAGRAM

C409207E10
0.5,1.708 0.958,1.906 0.458,0.198 10 false M19 0.49,1.875 2.167,2.354 1.677,0.479 10 false Front Seat Cushion Airbag Assembly RH 1.698,0.313 1.844,0.49 0.146,0.177 10 false 2 1.688,1.115 1.833,1.292 0.146,0.177 10 false 1 5.302,0.344 5.51,0.521 0.208,0.177 10 false 5 5.302,1.115 5.49,1.292 0.188,0.177 10 false 6 5.594,0.448 6.146,0.698 0.552,0.25 10 false FCP+ 5.594,1.229 6.125,1.521 0.531,0.292 10 false FCP- 5.417,1.708 5.875,1.906 0.458,0.198 10 false M15 5.417,1.865 7.063,2.156 1.646,0.292 10 false Airbag Sensor Assembly 1.229,0.333 1.781,0.583 0.552,0.25 10 false FCP+ 1.26,1.104 1.792,1.396 0.531,0.292 10 false FCP-

CAUTION / NOTICE / HINT

NOTICE:
·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.CHECK CONNECTORS
a.
C280784C05
0.469,1.104 0.781,1.302 0.313,0.198 10 false *1 1.292,1.469 1.604,1.667 0.313,0.198 10 false *3 2.385,1.583 2.698,1.781 0.313,0.198 10 false *2
*1 Front Seat Cushion Airbag Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire


Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the front seat cushion airbag assembly RH and airbag sensor assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the front seat cushion airbag assembly RH and airbag sensor assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT SEAT CUSHION AIRBAG ASSEMBLY RH

NG

REPLACE FLOOR WIRE

2.CHECK FRONT SEAT CUSHION AIRBAG ASSEMBLY RH
a.
C403338C02
0.417,2.333 0.833,2.583 0.417,0.25 2.167,2.542 2.323,2.656 2.323,2.656 2.469,2.656 true 1.229,0.958 1.76,1.448 0.531,0.49 10 false D 1.51,0.948 1.938,1.417 0.427,0.469 10 false C 1.927,0.948 2.438,1.375 0.51,0.427 10 false B 2.083,0.948 2.479,1.344 0.396,0.396 10 false A 2.479,1.26 2.99,1.708 0.51,0.448 10 false *2 1.177,0.677 1.615,1 0.438,0.323 10 false *1 0.417,1.719 0.76,2.198 0.344,0.479 10 false *a 2.469,2.521 2.927,2.854 0.458,0.333 10 false *3 0.5,2.375 1.031,2.667 0.531,0.292 10 false M19
*1 Front Seat Cushion Airbag Assembly RH
*2 Airbag Sensor Assembly
*3 SST
*a Front view of wire harness connector
(to Front Seat Cushion Airbag Assembly RH)


Connect the connector to the airbag sensor assembly.


b.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat cushion airbag assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


d.

Turn the power switch on (IG), and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTCs B1875, B1876, B1877 and B1878 are not output
DTC B1875, B1876, B1877 or B1878 is output


HINT:

Codes other than DTC B1875, B1876, B1877 and B1878 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.


k.

Disconnect SST from connector C.



DTCs B1875, B1876, B1877 and B1878 are not output

DTC B1875, B1876, B1877 or B1878 is output

3.CHECK FLOOR WIRE
3.CHECK FLOOR WIRE
a.
C403339C02
0.344,2.125 0.719,2.344 0.375,0.219 0.635,2.906 0.781,2.906 0.781,2.906 1.063,2.719 true 1.365,2.688 1.698,2.958 1.698,2.958 1.844,2.958 true 0.375,1.823 0.615,2.031 0.24,0.208 10 false *a 0.656,0.719 0.896,0.927 0.24,0.208 10 false *1 0.885,0.969 1.021,1.156 0.135,0.188 10 false D 1.281,0.969 1.417,1.156 0.135,0.188 10 false C 1.688,0.969 1.823,1.156 0.135,0.188 10 false B 2.094,0.958 2.229,1.146 0.135,0.188 10 false A 2.448,1.271 2.667,1.479 0.219,0.208 10 false *2 0.417,2.156 0.719,2.333 0.302,0.177 10 false M19 0.281,2.823 0.729,3.01 0.448,0.188 10 false FCP- 1.448,0.771 1.688,0.979 0.24,0.208 10 false *3 1.875,2.865 2.323,3.052 0.448,0.188 10 false FCP+
*1 Front Seat Cushion Airbag Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Cushion Airbag Assembly RH)
V100135

Release the activation prevention mechanism


Disconnect the floor wire from the airbag sensor assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M19-2 (FCP+) - Body ground power switch on (IG) Below 1 V
M19-1 (FCP-) - Body ground power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal, and wait for at least 90 seconds.



c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M19-2 (FCP+) - M19-1 (FCP-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M19-2 (FCP+) - Body ground Always 1 MΩ or higher
M19-1 (FCP-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M19-2 (FCP+) - M19-1 (FCP-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

REPLACE FLOOR WIRE

4.CHECK DTC
a.
C238241C29
0.729,1.521 1.042,1.719 0.313,0.198 10 false *1 2.167,1.594 2.479,1.792 0.313,0.198 10 false *2
*1 Front Seat Cushion Airbag Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat cushion airbag assembly RH and airbag sensor assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal, and wait for at least 2 seconds.


c.

Turn the power switch on (IG), and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
Result:
Proceed to
DTCs B1875, B1876, B1877 and B1878 are not output
DTC B1875, B1876, B1877 or B1878 is output


HINT:

Codes other than DTC B1875, B1876, B1877 and B1878 may be output at this time, but they are not related to this check.




DTCs B1875, B1876, B1877 and B1878 are not output

DTC B1875, B1876, B1877 or B1878 is output