Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SRS SEAT CUSHION AIRBAG ASSEMBLY › 2018.10–2020.08
RM3620E _58 Vehicle Interior _076036 SUPPLEMENTAL RESTRAINT SYSTEMS _0374452 SRS SEAT CUSHION AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  SRS SEAT CUSHION AIRBAG ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat cushion airbag assembly RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system
·

for A25A-FKS:

(Click here)

·

for M20A-FKS:

(Click here)


Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Front passenger seat Zero point calibration (Occupant classification system)
·

Occupant classification system

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Front passenger seat Zero point calibration (Occupant classification system)
·

Occupant classification system

·

Passenger airbag ON/OFF indicator

·

Airbag system (Front passenger side)

·

Seat belt warning system (Front passenger)


(Click here)

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B475753

Be sure to read precaution thoroughly before servicing.



NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 6.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL


Hide 72551B 7.REMOVE RECLINING HINGE COVER RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY


Hide 72525A 8.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY


Hide 71811D 9.REMOVE FRONT SEAT CUSHION SHIELD RH

Hide 71861 10.REMOVE FRONT SEAT INNER CUSHION SHIELD RH

Hide 11.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY


Hide 12.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>DISASSEMBLY


Hide 739F0 13.REMOVE FRONT SEAT CUSHION AIRBAG ASSEMBLY RH

CAUTION:
B467367C01
0,0 0,0 false
V100155

Deployment Side


·

When storing the front seat cushion airbag assembly RH, keep the airbag deployment side facing upward.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.
B523157

Detach the 2 wire harness clamps.


b.

Detach the claw and disconnect the airbag connector.


c.
B523158C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the 2 nuts and front seat cushion airbag assembly RH.

CAUTION:
·

Do not reuse the nut.

·

If the installation surface or surrounding area of the front seat cushion airbag assembly RH is deformed or damaged, replace the front seat adjuster assembly RH with a new one.