The passenger side buckle switch circuit consists of the occupant detection ECU and front seat inner belt assembly RH (front passenger side buckle switch).
DTC B1771 is stored when a malfunction is detected in the front passenger side buckle switch circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1771 | Passenger Side Buckle Switch Circuit Malfunction | ·
The occupant detection ECU detects a line short, short to ground or B+, or an open in the front passenger side buckle switch circuit. ·
Front passenger side buckle switch malfunction ·
Occupant detection ECU malfunction |
·
Front seat wire RH ·
Front seat inner belt assembly RH (Front passenger side buckle switch) ·
Occupant detection ECU |
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
When DTC B1650 is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1771 is output, perform troubleshooting for this DTC first.
If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.
In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the occupant detection ECU and front seat inner belt assembly RH.
| Proceed to |
|---|
| Connectors are properly connected |
| Connectors are not properly connected |
Connectors are properly connected
Connectors are not properly connected
Disconnect the connectors from the occupant detection ECU and front seat inner belt assembly RH.
Check that the connectors (on the occupant detection ECU side and front seat inner belt assembly RH side) are not damaged.
| Proceed to |
|---|
| Connectors are not deformed or damaged |
| Connectors are deformed or damaged |
Connectors are not deformed or damaged
Connectors are deformed or damaged
| *1 | Front Seat Inner Belt Assembly RH |
| *2 | Occupant Detection ECU |
| *3 | Front Seat Wire RH |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Occupant Detection ECU) |
| *b | Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| S21-7 - Body ground | Engine switch on (IG) | Below 1 V |
| S21-9 - Body ground |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 1 and 2 of connector C.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S21-7 - S21-9 | Always | Below 1 Ω |
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S21-7 - S21-9 | Always | 1 MΩ or higher |
| S21-7 - Body ground | ||
| S21-9 - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connectors to the occupant detection ECU and front seat inner belt assembly RH.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the occupant detection ECU.
Clear the DTCs stored in the airbag sensor assembly.
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check the DTCs stored in the occupant detection ECU.
| Proceed to |
|---|
| DTC B1771 is output |
| DTC B1771 is not output |
Codes other than DTC B1771 may be output at this time, but they are not related to this check.
DTC B1771 is output
DTC B1771 is not output
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the front seat inner belt assembly RH with a new one.
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY (for Manual Seat)>REMOVAL
Perform the inspection using parts from a normal vehicle if possible.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the occupant detection ECU.
Clear the DTCs stored in the airbag sensor assembly.
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check the DTCs stored in the occupant detection ECU.
| Proceed to |
|---|
| DTC B1771 is not output |
| DTC B1771 is output |
Codes other than DTC B1771 may be output at this time, but they are not related to this check.
DTC B1771 is not output
DTC B1771 is output
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the occupant detection ECU with a new one.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>OCCUPANT CLASSIFICATION ECU>REMOVAL
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform "Zero Point Calibration".
| Tester Display |
|---|
| Zero Point Calibration |
| Proceed to |
|---|
| NEXT |
NEXT