Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for RHD) › 2018.10–2020.08
RM3620E _57 Power Source / Network _076180 POWER DISTRIBUTION _0371062 MAIN BODY ECU(for RHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the main body ECU (multiplex network body ECU) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for HV model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for HV model) (Click here)
Reset back door close position Power back door system (for HV model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of main body ECU (multiplex network body ECU) Code registration
·

Wireless door lock control system (for Entry function, HV model)

·

Entry and start system (for Entry function, HV model)

·

Entry and start system (for Start function, HV model)

·

Hybrid control system cannot be started


See Service Bulletin for the registration method.

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative (-) auxiliary battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system for A25A-FKS:
(Click here)
for M20A-FKS:
(Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
w/ Entry and Start System:

Replacement of main body ECU (multiplex network body ECU)


Code registration
·

Wireless door lock control system (for Entry function, Gasoline model)

·

Entry and start system (for Entry function, Gasoline model)

·

Entry and start system (for Start function, Gasoline model)

·

Engine start function


See Service Bulletin for the registration method.

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B473126

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.



NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Do not remove the main body ECU (multiplex network body ECU) except when replacing it.

·

When removing the main body ECU (multiplex network body ECU), always replace it with a new one.



Hide 58410B 2.REMOVE DECK BOARD ASSEMBLY (for HV Model)

Hide 58416K 3.REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 65351A 4.REMOVE BATTERY HOLE COVER (for HV Model)

Hide 5.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 58810J 6.REMOVE CONSOLE BOX ASSEMBLY

Hide 67914B 7.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 8.REMOVE COWL SIDE TRIM BOARD LH

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


Hide 55607 9.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55550 10.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 55433B 11.REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 89981 12.REMOVE HYBRID VEHICLE CONTROL ECU ASSEMBLY (for HV Model)

Hide 13.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for HV Model)

a.
E405828

Disconnect the 3 connectors.


b.

Detach the wire harness clamp.


c.
E405829C01
0,0 0,0 false
V100135

Nut
V100136

Bolt


Remove the nut and bolt.


d.

Detach the claw and disconnect the instrument panel junction block assembly with main body ECU.


e.
E405830

Detach the wire harness clamp.


f.
E405831

Detach the claw and remove the instrument panel junction block assembly with main body ECU from the connector holder.


g.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the 2 lever connectors.

E405832C01
1,1.646 1.448,1.646 1.448,1.646 1.448,2.875 true 0.99,2.063 1.448,2.063 true 1.385,2.927 1.698,3.083 0.313,0.156 10 false *a
*a Lever Connector - -
V113147

Rotate in this Direction
V100155

Protective Tape



h.

Detach the wire harness clamp and remove the instrument panel junction block assembly with main body ECU.


Hide 89261A 14.REMOVE ENGINE STOP AND START ECU (for Gasoline Model, with Stop and Start System)

Hide 15.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for Gasoline Model)

a.

w/ Stop and Start System:

i.
E405828

Disconnect the 3 connectors.


ii.

Detach the wire harness clamp.



b.

w/o Stop and Start System:

i.
E405825

Disconnect the 3 connectors.


ii.

Detach the wire harness clamp.


iii.
E405826C01
1.802,0.604 2.417,0.604 true 1.802,1.083 2.146,1.083 2.146,1.083 2.146,0.604 true 2.49,0.521 2.708,0.688 0.219,0.167 10 true *a
*a Lever Connector
V113147

Rotate in this Direction
V100155

Protective Tape


Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the 2 lever connectors.


iv.

Detach the wire harness clamp.


v.

Disconnect the 2 connectors.


vi.
E405827

Disconnect the 5 connectors.



c.
E405829C01
0,0 0,0 false
V100135

Nut
V100136

Bolt


Remove the nut and bolt.


d.

Detach the claw and disconnect the instrument panel junction block assembly with main body ECU.


e.
E405830

Detach the wire harness clamp.


f.
E405831

Detach the claw and remove the instrument panel junction block assembly with main body ECU from the connector holder.


g.

Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the claw and disconnect the 2 lever connectors.

E405832C01
1,1.646 1.448,1.646 1.448,1.646 1.448,2.875 true 0.99,2.063 1.448,2.063 true 1.385,2.927 1.698,3.083 0.313,0.156 10 false *a
*a Lever Connector - -
V113147

Rotate in this Direction
V100155

Protective Tape



h.

Detach the wire harness clamp and remove the instrument panel junction block assembly with main body ECU.


Hide 89221 16.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

a.
E405833

Detach the claw and remove the junction block bracket from the instrument panel junction block assembly with main body ECU.


b.

Press the lock of the instrument panel junction block assembly and release the lock of the main body ECU (multiplex network body ECU) as shown in the illustration.

E403056C01
4.271,4.479 4.698,4.479 false 4.906,5.146 4.906,4.708 false 4.854,5.188 5.167,5.344 0.313,0.156 10 false *a 4.083,4.396 4.396,4.552 0.313,0.156 10 false *b
*a Instrument Panel Junction Block Assembly *b Main Body ECU (Multiplex Network Body ECU)
V113147

Movement Direction
V100155

Instrument Panel Junction Block Assembly Lock



c.

While pressing the lock, horizontally insert a thin-bladed screwdriver with its tip wrapped with protective tape between the main body ECU (multiplex network body ECU) and instrument panel junction block assembly.

NOTICE:

Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).


E403057C01
0,0 0,0 false
V113147

Horizontally Insert a Thin-bladed Screwdriver
V100155

Protective Tape



d.
E403058C01
0.615,1.604 1.229,1.604 true 0.427,1.521 0.74,1.677 0.313,0.156 10 false *a
*a Internal Connector
V113147

Insert a Thin-bladed Screwdriver in this Direction
V113148

Released in this Direction
V100155

Protective Tape


When the thin-bladed screwdriver with its tip wrapped with protective tape is inserted, the internal connector lock is released.

NOTICE:
·

Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).

·

Do not excessively insert the screwdriver. Otherwise, the internal connector terminals may become deformed or damaged.

·

Replace the instrument panel junction block assembly when the connector terminal, the locking section, or the case is damaged or deformed.




e.
E403059

Hold the rib of the main body ECU (multiplex network body ECU).


f.
E403060C01
0,0 0,0 false
V113147

Rotate in this Direction


While rotating the main body ECU (multiplex network body ECU), completely release the lock.


g.
E403061C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.