Use the same procedure as for the LHD and RHD vehicles.
The procedure listed below is for the LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
58810J
1.INSTALL CONSOLE BOX ASSEMBLY
|
Install in this Direction |
Insert the guide and set the console box assembly into place in the direction indicated by the arrow shown in the illustration.
Install the 4 bolts.
except Manual Transaxle:
Attach the clamp to install the 2 bolts.
for Manual Transaxle:
Install the 2 bolts.
Connect each connector.
58815F
2.INSTALL CONSOLE BOX CARPET
Install the console box carpet.
58825A
3.INSTALL CONSOLE BOX POCKET (w/ Console Box Tray)
Install the console box pocket.
58816C
4.INSTALL FRONT NO. 1 CONSOLE BOX INSERT
Insert in the direction indicated by the arrow (1) shown in the illustration to attach the guide.
Rotate in the direction indicated by the arrow (2) shown in the illustration to attach the clip and install the front No. 1 console box insert.
| *A | for LHD | *B | for RHD |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
58817A
5.INSTALL FRONT NO. 2 CONSOLE BOX INSERT
Insert in the direction indicated by the arrow (1) shown in the illustration to attach the guide.
Rotate in the direction indicated by the arrow (2) shown in the illustration to attach the clip and install the front No. 2 console box insert.
| *A | for LHD | *B | for RHD |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
58903A
6.INSTALL REAR CONSOLE END PANEL SUB-ASSEMBLY
Connect each connector.
|
Install in this Direction |
Attach the clip and claw to install the rear console end panel sub-assembly in the direction indicated by the arrow shown in the illustration.
58803C
7.INSTALL CONSOLE CUP HOLDER BOX SUB-ASSEMBLY
w/ Illumination:
Connect the connector.
Attach the guide and clip to install the console cup holder box sub-assembly.
58805C
8.INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY
|
Install in this Direction |
Attach the guide in the direction indicated by the arrow shown in the illustration.
|
Install in this Direction |
Attach the clip to install the rear upper console panel sub-assembly in the direction indicated by the arrow shown in the illustration.
Install the bolt.
58813
9.INSTALL UPPER CONSOLE BOX (w/o Wireless Charger)
w/ Radio Receiver:
Attach the clamp and connect the 2 connectors.
| *A | except Manual Transaxle | *B | for Manual Transaxle |
w/o Radio Receiver:
Attach the clamp and connect the connector.
| *A | except Manual Transaxle | *B | for Manual Transaxle |
Insert in the direction indicated by the arrow (1) shown in the illustration to attach the guide.
Rotate in the direction indicated by the arrow (2) shown in the illustration to attach the clip and install the upper console box.
| *A | except Manual Transaxle | *B | for Manual Transaxle |
|
Install in this Direction (1) |
|
Install in this Direction (2) |
861C0
10.INSTALL MOBILE WIRELESS CHARGER CRADLE ASSEMBLY (w/ Wireless Charger)
58804A
11.INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
| *A | except Manual Transaxle |
| *B | for Manual Transaxle |
Connect the 2 connectors.
except Manual Transaxle:
|
Install in this Direction |
Attach the claw and clip to install the upper console panel sub-assembly.
for Manual transaxle:
|
Install in this Direction |
Attach the clip to install the upper console panel sub-assembly.
33504F
12.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)
|
Install in this Direction |
Twist the shift lever knob sub-assembly in the direction indicated by the arrow to install it.
33504F
13.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (except Manual Transaxle)
for Automatic Transaxle:
for CVT:
K120: Click hereDrivetrain>K120 (MULTIDRIVE / CVT)>SHIFT LEVER KNOB>INSTALLATION
K120F: Click hereDrivetrain>K120F (MULTIDRIVE / CVT)>SHIFT LEVER KNOB>INSTALLATION
for HV Model:
55606
14.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
w/ Foot Light:
Attach the claw to install the DLC3.
Attach the clamp and connect the connector.
w/o Foot Light:
Attach the claw to install the DLC3.
Even if there is no foot light, if there is a connector, connect the connector and attach the clamp.
|
Install in this Direction |
Insert the guide in the direction indicated by the arrow shown in the illustration.
|
Install in this Direction |
Lift up in the direction indicated by the arrow shown in the illustration to attach the guide and claw to install the No. 1 instrument panel under cover sub-assembly.
Install the 3 screws.
62111C
15.INSTALL COWL SIDE TRIM BOARD RH (for RHD)
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION
67913B
16.INSTALL FRONT DOOR SCUFF PLATE RH (for RHD)
Use the same procedure described for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION