Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › 2018.10–2019.02
RM3620E _58 Vehicle Interior _076053 INTERIOR PANELS / TRIM _0370160 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for LHD)

a.

Push in the direction indicated by the arrow shown in the illustration and insert the guide to set the instrument panel safety pad assembly.

B523240C01
0,0 0,0 false
V113147

Install in this Direction - -



b.

Install the instrument panel safety pad assembly with the 5 bolts <B>, nut <E> and 2 clips <D>.


c.

Attach the clamp.

B523238C02
0,0 0,0 false
V100135

Bolt <B>
V100136

Nut <E>
V100137

Clip <D> - -



d.
B523270

for Automatic Air Conditioning System:

Attach the claw to install the cooler (room temp. sensor) thermistor.


e.
B523236

Install the steering column assembly with 2 nuts for the instrument panel reinforcement assembly.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


f.
B523237

w/ Interior Illumination:

Connect the connector.


g.
B523265

Connect each connector.


h.
B523269C02
0,0 0,0 false
V100135

Bolt <C>


Install the 2 bolts <C>.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


i.
B523235

Connect the connector and attach the guide.


j.

Connect the airbag connector.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.


B529119C01
0.208,2.042 0.583,2.281 0.375,0.24 12 false *A 3.25,2.031 3.625,2.271 0.375,0.24 12 false *B
*A for Dual Type *B for Single Type
V113147

Slide in this Direction - -



Hide 2.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for RHD)

a.

Push in the direction indicated by the arrow shown in the illustration and insert the guide to set the instrument panel safety pad assembly.

B529095C01
0,0 0,0 false
V113147

Install in this Direction - -



b.

Install the instrument panel safety pad assembly with the 5 bolts <B>, nut <E> and 2 clips <D>.


c.

Attach the clamp.

B529093C02
0,0 0,0 false
V100135

Bolt <B>
V100136

Nut <E>
V100137

Clip <D> - -



d.
B529092

for Automatic Air Conditioning System:

Attach the claw to install the cooler (room temp. sensor) thermistor.


e.
B529091

Install the steering column assembly with 2 nuts for the instrument panel reinforcement assembly.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


f.
B529090

w/ Interior Illumination:

Connect the connector.


g.
B529089

Connect each connector.


h.
B529088C02
0,0 0,0 false
V100135

Bolt <C>


Install the 2 bolts <C>.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


i.
B529087

Connect the connector and attach the guide.


j.

Connect the airbag connector.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.


B529121C01
0,0 0,0 false
V113147

Slide in this Direction - -



Hide 45287 3.INSTALL LOWER STEERING COLUMN COVER

Hide 84330 4.INSTALL HAZARD WARNING SIGNAL SWITCH ASSEMBLY

Hide 86160P 5.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (except 4 Speakers)

Hide 86160L 6.INSTALL FRONT NO. 4 SPEAKER ASSEMBLY (for eCall)

Hide 55535B 7.INSTALL NO. 2 SPEAKER HOLE COVER

a.
B523241C01
0,0 0,0 false
V113147

Install in this Direction


Insert the guide in direction indicated by the arrow shown in the illustration.


b.
B523242C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip to install the No. 2 speaker hole cover as shown in the illustration.


Hide 62211 8.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 55317A 9.INSTALL INSTRUMENT SIDE PANEL RH

a.

for LHD, w/ Airbag Cut Off Switch:

Connect the connector.


b.
B523243C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide as shown in the illustration.


c.
B523244C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip to install the instrument side panel RH as shown in the illustration.


Hide 55475A 10.INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

a.
B523245C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip to install the No. 2 instrument cluster finish panel garnish as shown in the illustration.


Hide 55433B 11.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

a.
B523246C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip to install the lower No. 2 instrument panel finish panel as shown in the illustration.


b.
B523228C02
0,0 0,0 false
V100135

Bolt <B>
V100136

Screw <A>


Install the 3 screws <A> and 2 bolts <B>.


Hide 55550 12.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

a.
B529117C01
0.531,0.135 0.844,0.292 0.313,0.156 10 false *a 2.031,0.125 2.344,0.281 0.313,0.156 10 false *b
*a Assembly Position
*b Closed Position
V113147

Install in this Direction


With the glove compartment door assembly opened position, attach the hinge horizontally.

NOTICE:

Attach the hinges from the top will deform the hinges. Be sure to install the glove compartment door assembly horizontally.



b.
B529116C01
2.958,0.781 2.813,0.573 true 3.115,2.958 2.969,2.75 true 3.094,2.917 3.344,3.115 0.25,0.198 10 true *1 3.01,0.729 3.25,0.938 0.24,0.208 10 true *a 0.479,0.854 0.646,1.063 0.167,0.208 10 true A 2.948,1.271 3.115,1.469 0.167,0.198 10 true B
*1 Glove Compartment Door Stopper Sub-assembly
*a Stopper
V113147

Install in this Direction


Slightly bend the stoppers (A) and (B) in the directions indicated by the arrows in the illustration and attach the stoppers to install the glove compartment door assembly.


c.

Attach the claw to install the glove compartment door stopper sub-assembly.


Hide 55607 13.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B523226

w/ Foot Light:

Attach the clamp and connect the connector.

HINT:
B531219

Even if there is no foot light, if there is a connector, connect the connector and attach the clamp.



b.
B523247C01
0,0 0,0 false
V113147

Install in this Direction


Insert the guide in the direction indicated by the arrow shown in the illustration.


c.
B523248C03
1.208,2.74 1.5,2.938 0.292,0.198 10 true (1) 0.385,2.771 0.688,2.969 0.302,0.198 10 true (2) 2.073,2.719 2.365,2.917 0.292,0.198 10 true (3) 2.74,2.677 3.104,2.865 0.365,0.188 10 true (4)
V113147

Install in this Direction


Lift up in the installation direction, attach the claw in the order shown in the illustration to install the No. 2 instrument panel under cover sub-assembly.


Hide 62111C 14.INSTALL COWL SIDE TRIM BOARD RH

a.
B529098C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clamp and clip to install the cowl side trim board RH in the direction indicated by the arrow shown in the illustration.


b.
B529096

Install the cap nut.


Hide 67913B 15.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 62311B 16.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.

Install the front door opening trim weatherstrip RH.


Hide 86160P 17.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (except 4 Speakers)

Hide 55525 18.INSTALL NO. 1 SPEAKER HOLE COVER

a.
B523249C02
0,0 0,0 false
V113147

Install in this Direction


Insert the guide in direction indicated by the arrow shown in the illustration.


b.
B523250C02
0,0 0,0 false
V113147

Install in this Direction


Attach the clip to install the No. 1 speaker hole cover as shown in the illustration.


Hide 62212 19.INSTALL FRONT PILLAR GARNISH LH

Hide 73900 20.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Hide 55480D 21.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

a.

w/ Entry and Start System:

Connect the connector.


b.
B523251C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip to install the lower instrument panel finish panel assembly as shown in the illustration.


Hide 55545 22.INSTALL FUSE BOX OPENING COVER (for LHD)

a.

for HV Model:

Connect the connector.


b.
B523219C02
0.052,0.052 0.427,0.292 0.375,0.24 12 false *A 0.052,2.521 0.427,2.76 0.375,0.24 12 false *B
*A for 6 Switch Type
*B for 3 Switch Type


Attach the clamp.


c.

Connect each connector.


d.
B523252C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip to install the fuse box opening cover as shown in the illustration.


e.
B523217C02
0,0 0,0 false
V100135

Bolt <B>


Install the bolt <B>.


Hide 55545 23.INSTALL FUSE BOX OPENING COVER (for RHD)

a.

for HV Model:

Connect the connector.


b.
B529081

Connect each connector.


c.
B529086C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip to install the fuse box opening cover as shown in the illustration.


d.
B529079C02
0,0 0,0 false
V100135

Bolt <B>


Install the bolt <B>.


Hide 77306 24.INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for Gasoline Model)

a.
B529078C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and claw to install the fuel lid lock open lever sub-assembly in the direction indicated by the arrow as shown in the illustration.


Hide 53601 25.INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B529077C01
0,0 0,0 false
V113147

Install in this direction


Attach the guide and claw to install the hood lock control lever sub-assembly in the direction indicated by the arrow shown in the illustration.


Hide 55318C 26.INSTALL INSTRUMENT SIDE PANEL LH

a.

for RHD, w/ Airbag Cut Off Switch:

Connect the connector.


b.
B523253C02
0,0 0,0 false
V113147

Install in this Direction


Attach the guide as shown in the illustration.


c.
B523254C02
0,0 0,0 false
V113147

Install in this Direction


Attach the clip to install the instrument side panel LH as shown in the illustration.


Hide 62312B 27.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Install the front door opening trim weatherstrip LH.


Hide 55606 28.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

a.
B523212

w/ Foot Light:

i.

Attach the claw to install the DLC3.


ii.

Attach the clamp and connect the connector.



b.

w/o Foot Light:

i.
B531218

Attach the claw to install the DLC3.

HINT:

Even if there is no foot light, if there is a connector, connect the connector and attach the clamp.




c.
B523255C01
0,0 0,0 false
V113147

Install in this Direction


Insert the guide in the direction indicated by the arrow shown in the illustration.


d.
B523256C01
0,0 0,0 false
V113147

Install in this Direction


Lift up in the direction indicated by the arrow shown in the illustration to attach the guide and claw to install the No. 1 instrument panel under cover sub-assembly.


e.
B523210C01
0,0 0,0 false
V100135

Screw <A>


Install the 3 screws <A>.


Hide 62112 29.INSTALL COWL SIDE TRIM BOARD LH (for LHD)

a.
B523257C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and clip to install the cowl side trim board LH in the direction indicated by the arrow shown in the illustration.


b.
B523208

Install the cap nut.


Hide 67914B 30.INSTALL FRONT DOOR SCUFF PLATE LH (for LHD)

Hide 55434B 31.INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL

a.

Connect each connector.


b.
B523258C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip to install the lower center instrument panel finish panel.


Hide 55900 32.INSTALL AIR CONDITIONING CONTROL ASSEMBLY

Hide 83100 33.INSTALL COMBINATION METER ASSEMBLY

Hide 55410C 34.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.
B523261C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip to install the instrument cluster finish panel assembly.


b.
B523262C02
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and guide.


Hide 55474B 35.INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH

a.
B523264C01
0,0 0,0 false
V113147

Install in this Direction


Attach the guide and clip to install the instrument cluster finish panel garnish as shown in the illustration.


Hide 36.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)

Hide 37.INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)

Hide 38.INSTALL STEREO OPENING COVER WITH BRACKET (for Type A, w/ Cover)

a.
B557516C02
0,0 0,0 false
V113147

Install in this Direction


Attach the clip to install the stereo opening cover with bracket as shown in the illustration.


b.
B529069N01
0.25,0.542 0.406,0.74 0.156,0.198 10 true 1 3.052,0.365 3.208,0.563 0.156,0.198 10 true 2 0.365,0.958 0.521,1.156 0.156,0.198 10 true 4 2.938,0.927 3.094,1.125 0.156,0.198 10 true 3

Install the 4 bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 55422C 39.INSTALL CENTER UPPER INSTRUMENT CLUSTER FINISH PANEL

a.
B529074C01
0,0 0,0 false
V113147

Install in this Direction


for Type A:

Attach the clip to install the center upper instrument cluster finish panel.


b.
B523268C01
0,0 0,0 false
V113147

Install in this Direction


for Type B:

Attach the clip to install the center upper instrument cluster finish panel.


Hide 55424C 40.INSTALL RADIO TUNER FINISH PANEL (for Type A, w/ Radio Tuner Cover)

a.
B529073C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip to install the radio tuner finish panel as shown in the illustration.


Hide 55405B 41.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (for Type A)

a.
B529099C01
0,0 0,0 false
V113147

Install in this Direction


Attach the clip and claw to install the center instrument cluster finish panel sub-assembly as shown in the illustration.


Hide 43.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 65351A 44.INSTALL BATTERY HOLE COVER (for HV Model)

Hide 58416K 45.INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)

Hide 58410B 46.INSTALL DECK BOARD ASSEMBLY (for HV Model)

Hide 49.PERFORM SYSTEM INITIALIZATION AND CALIBRATION