Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM3620E _58 Vehicle Interior _076046 DOOR LOCK _0370163 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives switch signals from the door control switch assembly. The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.

WIRING DIAGRAM

B522710E04
5.375,2.615 7.021,3.198 1.646,0.583 10 false Main Body ECU (Multiplex Network Body ECU) 4.052,1.75 5.698,2.333 1.646,0.583 10 false Instrument Panel Junction Block Assembly 1.177,1.875 3.083,2.521 1.906,0.646 10 false Door Control Switch Assembly 4.125,0.646 5.771,1.229 1.646,0.583 10 false 4D 5.51,1.219 7.156,1.802 1.646,0.583 10 false 22 5.51,0.573 7.156,1.156 1.646,0.583 10 false 20 1.219,1.729 2.865,2.313 1.646,0.583 10 false I4 4.125,0.469 5.771,1.052 1.646,0.583 10 false 16 4.125,1.135 5.771,1.719 1.646,0.583 10 false 39 5.74,0.573 6.26,1.219 0.521,0.646 10 false L1 5.74,1.219 6.26,1.865 0.521,0.646 10 false UL1 6.01,0.281 6.531,0.927 0.521,0.646 10 false +B 6.031,0.958 6.552,1.604 0.521,0.646 10 false +B 2.802,0.552 4.448,1.135 1.646,0.583 10 false 4 2.823,1.208 4.469,1.792 1.646,0.583 10 false 2 1.115,1.219 2.76,1.802 1.646,0.583 10 false 5 1.281,1.219 1.802,1.865 0.521,0.646 10 false E 1.833,0.76 2.354,1.406 0.521,0.646 10 false LOCK 1.75,1.438 2.583,2.073 0.833,0.635 10 false UNLOCK 2.615,0.563 3.135,1.208 0.521,0.646 10 false L 2.552,1.219 3.073,1.865 0.521,0.646 10 false UL 5.385,2.469 5.906,3.115 0.521,0.646 10 false A 4.135,1.302 5.781,1.885 1.646,0.583 10 false 4A

CAUTION / NOTICE / HINT

NOTICE:

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.*

*: w/ Entry and Start System


PROCEDURE

1.READ VALUE USING GTS (Door Lock SW-Lock, Door Lock SW-Unlock)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Door Lock SW-Lock Front passenger door control switch lock signal OFF or ON OFF: Lock side of front passenger door control switch not pushed
ON: Lock side of front passenger door control switch pushed
-
Door Lock SW-Unlock Front passenger door control switch unlock signal OFF or ON OFF: Unlock side of front passenger door control switch not pushed
ON: Unlock side of front passenger door control switch pushed
-
Body Electrical > Main Body > Data List
Tester Display
Door Lock SW-Lock
Door Lock SW-Unlock
50003 123 17,18
OK:

The GTS indicates ON or OFF according to the switch operation shown in the table.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.INSPECT DOOR CONTROL SWITCH ASSEMBLY
2.INSPECT DOOR CONTROL SWITCH ASSEMBLY
a.

Remove the door control switch assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>REMOVAL


b.

Inspect the door control switch assembly.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE DOOR CONTROL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect the I4 door control switch assembly connector.


b.

Disconnect the 4A and 4D instrument panel junction block assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I4-4 (L) - 4D-16 Always Below 1 Ω
I4-2 (UL) - 4A-39 Always Below 1 Ω
I4-5 (E) - Body Ground Always Below 1 Ω
I4-4 (L) or 4D-16 - Other terminals and body ground Always 10 kΩ or higher
I4-2 (UL) or 4A-39 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

B535521C01
1.875,1.792 2.281,2 0.406,0.208 1.938,0.177 2.344,0.385 0.406,0.208 5.448,0.698 5.854,0.906 0.406,0.208 0.146,0.073 2.458,1.99 2.313,1.917 10 false *a 2.042,1.813 2.198,2.01 0.156,0.198 10 false A 2.073,0.208 2.5,0.438 0.427,0.229 10 false 4A 5.552,0.729 5.979,0.958 0.427,0.229 10 false 4D
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
A-20 (L1) - 4D-16 Always Below 1 Ω
A-22 (UL1) - 4A-39 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY