Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)
RM3620E _56 Audio / Visual / Telematics _076047 AUDIO / VIDEO _0370279 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E408081E01
1.969,0.25 3.26,0.469 1.292,0.219 10 false from TAIL Relay 6,1.073 6.354,1.281 0.354,0.208 10 false ILL+ 5.865,3.656 6.24,3.865 0.375,0.208 10 false G66 5.875,3.823 6.865,4.219 0.99,0.396 10 false Radio Receiver Assembly 3.219,0.948 3.635,1.198 0.417,0.25 10 false IL+2 4.063,0.417 4.771,0.594 0.708,0.177 10 false PANEL 3.74,1.083 4.125,1.292 0.385,0.208 10 false G20 2.729,1.094 2.99,1.281 0.26,0.188 10 false z6 2.719,2.281 2.979,2.469 0.26,0.188 10 false z6 2.844,2.646 4.042,3.125 1.198,0.479 10 false Spiral Cable Sub-assembly 0.615,2.604 1.875,2.958 1.26,0.354 10 false Steering Pad Switch RH Side 2.75,0.875 2.917,1.042 0.167,0.167 10 false 1 2.75,2.063 2.917,2.229 0.167,0.167 10 false 6 3.823,2.052 4.031,2.219 0.208,0.167 10 false 9 3.823,0.865 4.083,1.042 0.26,0.177 10 false 14 5.74,1 5.938,1.177 0.198,0.177 10 false 10 0.583,1.427 1.865,1.771 1.281,0.344 10 false Steering Pad Switch LH Side 0.333,3.5 2.365,3.74 2.031,0.24 10 false Steering Pad Switch Assembly 6.01,2.365 6.625,2.563 0.615,0.198 10 false GND1 5.792,2.24 5.969,2.427 0.177,0.188 10 false 7 5.781,0.385 7.073,0.604 1.292,0.219 10 false to Other Systems 3.74,2.281 4.125,2.49 0.385,0.208 10 false G20 3.219,2.135 3.635,2.385 0.417,0.25 10 false IL-2

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/o Occupant Classification System)>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio receiver assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.


Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except radio receiver assembly. B
No illumination comes on (radio receiver assembly, hazard switch, heater control switch, etc.). C



A

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY AND BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

C

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.
E270420C48
1.5,0.25 1.875,0.479 0.375,0.229 2.24,1.5 2.313,1.917 2.313,1.917 2.479,1.917 true 0.969,1.927 1.146,1.927 1.146,1.927 1.313,1.5 true 2.531,1.833 2.917,2.021 0.385,0.188 10 false IL+2 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 1.542,0.281 1.854,0.479 0.313,0.198 10 false G20 0.688,1.844 1.073,2.031 0.385,0.188 10 false IL-2
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Disconnect the spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G20-14 (IL+2) - Body ground Ignition switch ON
Light control switch in the tail or head position
11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G20-9 (IL-2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT INSPECTION PROCEDURE SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
E259248C48
1.51,0.396 1.896,0.594 0.385,0.198 2.417,1.698 2.25,1.698 2.25,1.698 2.104,1.365 true 1.219,1.688 1.375,1.688 1.375,1.688 1.563,1.365 true 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.573,0.417 1.917,0.625 0.344,0.208 10 false G66 2.469,1.625 3.021,1.844 0.552,0.219 10 false ILL+ 0.823,1.604 1.26,1.802 0.438,0.198 10 false GND1
*a Front view of wire harness connector
(to Radio Receiver Assembly)


Disconnect the radio receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G66-10 (ILL+) - Body ground Ignition switch ON
Light control switch in the tail or head position
11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G66-7 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR