Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)
RM3620E _56 Audio / Visual / Telematics _076047 AUDIO / VIDEO _0370279 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  USB Audio System Recognition/Play Error  


DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio receiver assembly. This diagnosis procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E402682E01
5.625,0.635 5.781,0.823 0.156,0.188 10 false 3 5.625,1.042 5.781,1.229 0.156,0.188 10 false 2 5.615,1.5 5.771,1.688 0.156,0.188 10 false 4 5.615,2.344 5.771,2.531 0.156,0.188 10 false 5 5.458,3.031 5.927,3.219 0.469,0.188 10 false G106 5.458,3.188 7.094,3.458 1.635,0.271 10 false Radio Receiver Assembly 1.531,0.625 1.771,0.823 0.24,0.198 10 false 10 1.583,1.031 1.74,1.219 0.156,0.188 10 false 9 1.542,1.5 1.781,1.677 0.24,0.177 10 false 11 1.594,1.875 1.76,2.125 0.167,0.25 10 false 8 0.417,3 0.885,3.188 0.469,0.188 10 false G16 0.406,3.167 3,3.344 2.594,0.177 10 false No. 1 Stereo Jack Adapter Assembly 1.021,0.771 1.563,0.958 0.542,0.188 10 false UDO+ 1.042,1.198 1.427,1.396 0.385,0.198 10 false UDO- 1.01,1.594 1.542,1.802 0.531,0.208 10 false UJSG 1.146,2.063 1.531,2.26 0.385,0.198 10 false UPI 5.885,0.781 6.323,1 0.438,0.219 10 false US1+ 5.875,1.177 6.458,1.427 0.583,0.25 10 false US1- 5.885,1.635 6.406,1.927 0.521,0.292 10 false UGD1 5.875,2.021 6.688,2.24 0.813,0.219 10 false USV1 1.042,2.469 1.427,2.667 0.385,0.198 10 false UJSS 1.563,2.323 1.854,2.563 0.292,0.24 10 false 12 5.875,2.427 6.688,2.646 0.813,0.219 10 false USG1 5.625,1.906 5.781,2.094 0.156,0.188 10 false 1 3.521,2.469 3.99,2.656 0.469,0.188 10 false * 0.458,3.458 3.052,3.635 2.594,0.177 10 false *: Shielded

CAUTION / NOTICE / HINT

HINT:
·

When a large amount of data is in a USB device, it may take a while before play begins.

·

When using a USB device, files that are copy protected or encrypted due to copyright reasons cannot be played.

·

When files are not played in the sorted order, perform the following procedure before inspection.

(a)

Add numbers in front of the file names.

(b)

Put the files in a folder and copy the folder data to the USB device.




PROCEDURE

1.CHECK USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.


b.

Check if playable files are present on the USB device or "iPod".

HINT:

Refer to System Description for playable files.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)>SYSTEM DESCRIPTION



c.

Check if the USB device is a compatible format or "iPod" is a compatible version.

HINT:

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)>SYSTEM DESCRIPTION



Result:
Result Proceed to
No playable files exist, or incompatible device format or version A
Playable files exist, and compatible device format or version B



A

END (USB DEVICE FORMAT IS INCOMPATIBLE, "iPod" VERSION IS INCOMPATIBLE, OR NO PLAYABLE FILES EXIST)

B

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.
E360495C63
1.542,0.198 1.958,0.469 0.417,0.271 1.521,2.219 1.938,2.49 0.417,0.271 2.167,1.958 1.76,1.51 true 1.833,1.188 2.292,1.219 true 1.833,1.354 2.292,1.5 true 1.052,1.406 1.573,1.167 true 1.031,1.75 1.552,1.375 true 1.906,3.656 2.396,3.771 true 1.417,4.083 1.656,3.76 true 0.958,4.063 1.635,3.667 true 0.906,3.708 1.521,3.656 true 2.135,4 1.792,3.656 true 0.24,0.188 0.552,0.385 0.313,0.198 10 false *a 0.24,2.802 0.552,3 0.313,0.198 10 false *b 0.688,1.375 1.135,1.552 0.448,0.177 10 false UGD1 0.698,1.729 1.125,1.938 0.427,0.208 10 false US1+ 2.198,1.927 2.688,2.167 0.49,0.24 10 false USG1 2.313,1.438 2.729,1.688 0.417,0.25 10 false US1- 0.646,3.635 0.958,3.833 0.313,0.198 10 false UPI 0.635,4.021 1.031,4.281 0.396,0.26 10 false UDO- 1.24,4.094 1.74,4.354 0.5,0.26 10 false UJSS 2.156,4 2.594,4.26 0.438,0.26 10 false UDO+ 2.427,3.708 2.927,3.948 0.5,0.24 10 false UJSG 1.594,0.25 2.031,0.458 0.438,0.208 10 false G106 1.594,2.271 1.906,2.469 0.313,0.198 10 false G16 2.313,1.146 2.74,1.375 0.427,0.229 10 false USV1
*a Front view of wire harness connector
(to Radio Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Disconnect the radio receiver assembly connector.


b.

Disconnect the No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G16-10 (UDO+) - G106-3 (US1+) Always Below 1 Ω
G16-9 (UDO-) - G106-2 (US1-) Always Below 1 Ω
G16-11 (UJSG) - G106-4 (UGD1) Always Below 1 Ω
G16-8 (UPI) - G106-1 (USV1) Always Below 1 Ω
G16-12 (UJSS) - G106-5 (USG1) Always Below 1 Ω
G16-10 (UDO+) - Body ground Always 10 kΩ or higher
G16-9 (UDO-) - Body ground Always 10 kΩ or higher
G16-11 (UJSG) - Body ground Always 10 kΩ or higher
G16-8 (UPI) - Body ground Always 10 kΩ or higher
G16-12 (UJSS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)
a.
E360496C33
1.573,0.594 1.938,0.844 0.365,0.25 1.99,2.5 2.844,2.052 true 1.438,2.51 0.802,2.365 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.635,0.635 1.948,0.833 0.313,0.198 10 false G16 0.51,2.281 0.917,2.531 0.406,0.25 10 false UPI 2.885,1.948 3.396,2.156 0.51,0.208 10 false UJSG
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Disconnect the No. 1 stereo jack adapter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G16-8 (UPI) - G16-11 (UJSG) Ignition switch ACC 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

NG

REPLACE RADIO RECEIVER ASSEMBLY

4.FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
a.

Delete all files in the USB device or "iPod" and format/restore it.


b.

Save the data again and check if it can be played on the in-vehicle device.

NOTICE:

Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that backup music data is available before performing this operation.


HINT:

Make sure to obtain the customer's permission to perform this procedure.


OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

5.REPLACE USB DEVICE OR "iPod"
5.REPLACE USB DEVICE OR "iPod"
a.

Turn the ignition switch off.

HINT:

When this malfunction occurs, it is necessary to turn off the ignition switch to make it possible for the vehicle to recognize a new device when it is connected.



b.

Turn the ignition switch to ACC.


c.

Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:
·

If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

·

Refer to System Description for compatible formats and versions.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)>SYSTEM DESCRIPTION




d.

Check if a USB device or "iPod" is recognized by the radio receiver assembly, and if information such as track, artist and album names, is displayed on the screen.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

NG