Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM (for HV Model)
RM3620E _51 Engine / Hybrid System _076038 CRUISE CONTROL _0370336 CRUISE CONTROL SYSTEM(for HV Model) J

CRUISE CONTROL  CRUISE CONTROL SYSTEM(for HV Model)  Steering Pad Switch Circuit  


DESCRIPTION

·

The steering pad switch assembly outputs the cruise control power supply switch signal and each operation switch signal to the hybrid vehicle control ECU assembly.

·

The hybrid vehicle control ECU assembly performs cruise control according to the signal from the steering pad switch assembly.


WIRING DIAGRAM

for LHD:
C374512E19
3.958,2.583 5.708,2.885 1.75,0.302 10 false Spiral Cable Sub-assembly 1.021,2.594 2.938,2.927 1.917,0.333 10 false Steering Pad Switch Assembly (Cruise Control Switch) 3.073,1.385 3.688,1.583 0.615,0.198 10 false MAIN 2.177,1.385 2.792,1.583 0.615,0.198 10 false CANCEL 1.313,1.385 1.927,1.583 0.615,0.198 10 false +RES 0.469,1.385 1.083,1.583 0.615,0.198 10 false -SET 3.854,2.083 4.167,2.281 0.313,0.198 10 false z6 3.844,0.875 4.156,1.073 0.313,0.198 10 false z6 3.885,0.677 4.042,0.875 0.156,0.198 10 false 2 3.854,1.875 4.083,2.073 0.229,0.198 10 false 12 4.667,0.792 5.125,0.99 0.458,0.198 10 false CCS 4.677,2 5.135,2.198 0.458,0.198 10 false ECC 5.531,0.875 5.99,1.073 0.458,0.198 10 false G20 5.521,2.083 5.979,2.281 0.458,0.198 10 false G20 5.563,0.667 5.823,0.875 0.26,0.208 10 false 13 5.604,1.875 5.76,2.073 0.156,0.198 10 false 2 6.417,0.885 6.875,1.083 0.458,0.198 10 false CCS 6.146,0.76 6.427,0.958 0.281,0.198 10 false 14 6.198,2.573 6.656,2.771 0.458,0.198 10 false A30 6.198,2.719 7.125,3.26 0.927,0.542 10 false Hybrid Vehicle Control ECU Assembly 3.313,0.99 3.771,1.188 0.458,0.198 10 false CCS 3.292,2.208 3.75,2.406 0.458,0.198 10 false ECC

for RHD:
C374512E20
4.156,2.583 5.552,2.958 1.396,0.375 10 false Spiral with Sensor Cable Sub-assembly 1.021,2.594 2.938,2.927 1.917,0.333 10 false Steering Pad Switch Assembly (Cruise Control Switch) 3.073,1.385 3.688,1.583 0.615,0.198 10 false MAIN 2.177,1.385 2.792,1.583 0.615,0.198 10 false CANCEL 1.313,1.385 1.927,1.583 0.615,0.198 10 false +RES 0.469,1.385 1.083,1.583 0.615,0.198 10 false -SET 3.854,2.083 4.167,2.281 0.313,0.198 10 false z6 3.844,0.875 4.156,1.073 0.313,0.198 10 false z6 3.885,0.677 4.042,0.875 0.156,0.198 10 false 2 3.854,1.875 4.083,2.073 0.229,0.198 10 false 12 4.667,0.792 5.125,0.99 0.458,0.198 10 false CCS 4.677,2 5.135,2.198 0.458,0.198 10 false ECC 5.531,0.875 5.99,1.073 0.458,0.198 10 false G20 5.521,2.083 5.979,2.281 0.458,0.198 10 false G20 5.563,0.667 5.823,0.875 0.26,0.208 10 false 13 5.604,1.875 5.76,2.073 0.156,0.198 10 false 2 6.417,0.885 6.875,1.083 0.458,0.198 10 false CCS 6.156,0.75 6.427,0.979 0.271,0.229 10 false 14 6.198,2.573 6.656,2.771 0.458,0.198 10 false G63 6.198,2.719 7.125,3.26 0.927,0.542 10 false Hybrid Vehicle Control ECU Assembly 3.323,1 3.781,1.198 0.458,0.198 10 false CCS 3.313,2.208 3.771,2.406 0.458,0.198 10 false ECC

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the hybrid vehicle control ECU assembly, refer to Service Bulletin.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for HV Model with Occupant Classification System)>PRECAUTION



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

Read the Data List according to the display on the GTS.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for HV Model)>DATA LIST / ACTIVE TEST

OK:

The Data List items shown in the table change according to the operation of the steering pad switch assembly.


Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status ON or OFF ON: CANCEL switch pushed
OFF: CANCEL switch not pushed
-
-SET Switch -SET switch status ON or OFF ON: -SET switch pushed
OFF: -SET switch not pushed
-
+RES Switch +RES switch status ON or OFF ON: +RES switch pushed
OFF: +RES switch not pushed
-
Cruise Main Switch Operation Condition Cruise control main switch status ON or OFF ON: Cruise control main switch pushed
OFF: Cruise controlmain switch not pushed
-
Powertrain > Cruise Control > Data List
Tester Display
Cancel Switch
-SET Switch
+RES Switch
Cruise Main Switch Operation Condition
50003 399 21,22,23,1

Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY AND BODY GROUND)
a.

Disconnect the G20 spiral cable sub-assembly connector.


b.

for LHD:

Disconnect the A30 hybrid vehicle control ECU assembly connector.


c.

for RHD:

Disconnect the G63 hybrid vehicle control ECU assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
G20-13 (CCS) - A30-14 (CCS) Always Below 1 Ω
G20-2 (ECC) - Body ground Always Below 1 Ω
G20-13 (CCS) or A30-14 (CCS) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
G20-13 (CCS) - G63-14 (CCS) Always Below 1 Ω
G20-2 (ECC) - Body ground Always Below 1 Ω
G20-13 (CCS) or G63-14 (CCS) - Body ground Always 10 kΩ or higher



e.

for RHD:

Connect the G63 hybrid vehicle control ECU assembly connector.


f.

for LHD:

Connect the A30 hybrid vehicle control ECU assembly connector.


g.

Connect the G20 spiral cable sub-assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU ASSEMBLY AND BODY GROUND)