Home › Drivetrain › UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL OIL SEAL
RM3620E _52 Drivetrain _076122 UB80E AUTOMATIC TRANSMISSION / TRANSAXLE _0370675 DIFFERENTIAL OIL SEAL A

UB80E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft oil seal LH and front drive shaft oil seal RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Front wheel alignment adjustment
·

Perform reset memory

·

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

PROCEDURE

Hide 43457 2.REMOVE DRIVE SHAFT BEARING BRACKET

Hide 43420H 3.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C402742N01
1.083,2.5 1.25,2.5 1.25,2.5 1.365,1.844 true 0.781,2.417 1.198,2.583 0.417,0.167 10 false SST

Using SST, remove the front drive shaft oil seal LH from the automatic transaxle case sub-assembly.

SST
09308-00010  

NOTICE:

Be careful not to damage the automatic transaxle case sub-assembly.



Hide 43410M 4.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C402743N01
2.271,1.333 2.667,1.25 2.667,1.25 2.833,1.25 true 2.885,1.167 3.302,1.333 0.417,0.167 10 false SST

Using SST, remove the front drive shaft oil seal RH from the transaxle housing.

SST
09308-00010  

NOTICE:

Be careful not to damage the transaxle housing.



Hide 43410M 5.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C402744C01
1.5,1.167 2.75,1 2.75,1 2.177,1.75 true 1.281,2.302 1.281,2.083 1.281,2.083 1.167,2.083 false 1.052,2.281 0.667,2.083 0.667,2.083 0.5,2.083 true 1.396,2.677 1.563,2.844 0.167,0.167 10 false *a 2.813,0.906 3.198,1.177 0.385,0.271 10 false SST 0.292,2 0.458,2.167 0.167,0.167 10 false *b 0.958,2 1.125,2.167 0.167,0.167 10 false *c
*a Depth
*b Inner Lip
*c Outer Lip


Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle housing.

SST
09316-10010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·
C381409C01
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


Make sure that the outer lip of the front drive shaft oil seal RH is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the front drive shaft oil seal RH.

·

Do not install the front drive shaft oil seal RH at an angle.

·

Do not remove the grease from the inner lip and outer lip of the front drive shaft oil seal RH.




Hide 43420H 6.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C402745C01
0.875,1.344 2.875,1.615 2.875,1.615 1.885,1.188 true 2.167,2.25 2.25,2.25 2.25,2.25 2.375,2.438 false 2.25,2.083 2.417,2.083 2.417,2.083 2.583,2.365 false 2.115,2.75 2.281,2.917 0.167,0.167 10 false *a 2.927,1.521 3.26,1.75 0.333,0.229 10 true SST 2.042,2 2.208,2.167 0.167,0.167 10 false *b 1.958,2.167 2.125,2.333 0.167,0.167 10 false *c
*a Depth
*b Inner Lip
*c Outer Lip


Using SST and a hammer, install a new front drive shaft oil seal LH to the automatic transaxle case sub-assembly.

SST
09649-17010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·
C381409C01
2.292,1.073 2.427,1.073 2.427,1.073 2.427,1.406 false 1.323,1.26 1.552,1.26 false 2.219,0.75 2.583,0.75 false 0.729,0.75 1.094,0.75 false 1.052,0.281 1.333,0.51 0.281,0.229 10 false *a 2.542,0.281 2.823,0.51 0.281,0.229 10 false *b 2.125,0.979 2.406,1.208 0.281,0.229 10 false *c 1.594,1.156 1.875,1.385 0.281,0.229 10 false *c 0.427,0.677 0.885,0.875 0.458,0.198 10 false SST 1.917,0.677 2.375,0.875 0.458,0.198 10 false SST
*a Correct
*b Incorrect
*c Outer Lip


Make sure that the outer lip of the front drive shaft oil seal LH is not pinched by SST.

·

Do not allow foreign matter to attach to the inner lip and outer lip of the front drive shaft oil seal LH.

·

Do not install the front drive shaft oil seal LH at an angle.

·

Do not remove the grease from the inner lip and outer lip of the front drive shaft oil seal LH.




Hide 43457 7.INSTALL DRIVE SHAFT BEARING BRACKET