Home › Engine / Hybrid System › A25A-FKS (ENGINE MECHANICAL) › ENGINE UNIT › 2018.10–2020.05
RM3620E _51 Engine / Hybrid System _076317 A25A-FKS ENGINE MECHANICAL _0371513 ENGINE UNIT A

A25A-FKS ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: When performing learning using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system (Click here)
Perform steering sensor zero point calibration Lane control system (Click here)
Parking support brake system (for Gasoline model)*
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (for Gasoline model) (Click here)
Reset back door close position Power back door system (for Gasoline model) (Click here)
Power back door initialization Power door lock control system (Click here)
Replacement of ECM
w/ Canister Pump Module:

Perform Vehicle Identification Number (VIN) registration


DTC P063051 is output (Click here)
w/o Canister Pump Module:

Perform Vehicle Identification Number (VIN) or frame number registration


(Click here)
ECU communication ID registration Engine start function See Service Bulletin for the registration method.
for UB80E:

If transaxle compensation code read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
for UB80F:

If transaxle compensation code read from ECM

-

Perform reset memory

-

Transfer transaxle compensation code

-

Perform road test to allow ECM to learn



·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired

·

Replacement of throttle body with motor assembly

·

Replacement of cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Replacement of camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing exhaust gear assembly

·

Replacement of port fuel injector assembly

·

Replacement of direct fuel injector assembly

·

Replacement of fuel pump assembly (for high pressure side)

·

Replacement of engine coolant temperature sensor

·

Replacement of spark plug

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Replacement of knock control sensor

·

Replacement of air fuel ratio sensor (sensor 2)


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


w/ Canister Pump Module:
(Click here)
w/o Canister Pump Module:
(Click here)
Replacement of automatic transaxle assembly
for UB80E:
·

Reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
for UB80F:
·

Reset memory

·

Input transaxle compensation code into ECM

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
Automatic transaxle fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly for UB60E:
(Click here)
for UB60F:
(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (for Gasoline model) (Click here)
Front wheel alignment adjustment
1.

Perform reset memory

2.

Perform acceleration sensor zero point calibration and store system information memorization.


·

VSC is disabled or malfunctions

·

DTCs are output

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Front bumper assembly (Including removal and installation)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (for Gasoline model) (Click here)
Front television camera view adjustment Panoramic view monitor system (for Gasoline model) (Click here)

NOTICE:
·

After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

·

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

Hide 43457 1.REMOVE DRIVE SHAFT BEARING BRACKET

a.
A429161C01
0.042,0.031 0.281,0.292 0.24,0.26 10 true *A 0.031,2.344 0.26,2.573 0.229,0.229 10 true *B
*A for 2WD
*B for 4WD/AWD


Remove the 3 bolts and drive shaft bearing bracket.


Hide 16361A 2.REMOVE V-RIBBED BELT

Hide 88310 4.REMOVE COMPRESSOR ASSEMBLY WITH PULLEY

a.

for Type A:

i.
E365913C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts and 2 nuts.


ii.
E365914

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and compressor assembly with pulley.



b.

for Type B:

i.
E371401

Remove the 4 bolts and compressor assembly with pulley.



Hide 12602C 5.REMOVE NO. 2 ENGINE COVER

a.
A402117

Remove the 2 bolts and No. 2 engine cover from the No. 2 timing chain cover assembly.


Hide 16620D 6.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

NOTICE:
A409240

·

Do not apply or add any oil or grease to the belt tensioner to prevent abnormal noises from the belt tensioner pulley, belt squealing, etc.

·

Do not allow oil or grease to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.



a.
A400315

Remove the 2 bolts and V-ribbed belt tensioner assembly from the No. 2 timing chain cover assembly.


Hide 11336A 7.REMOVE NO. 2 TIMING CHAIN COVER INSULATOR

a.
A400316

Remove the No. 2 timing chain cover insulator from the V-ribbed belt tensioner assembly.


Hide 11336A 8.REMOVE TIMING GEAR COVER INSULATOR

a.
A402700

Using an 8 mm socket wrench, remove the bolt, plate washer and timing gear cover insulator from the No. 2 timing chain cover assembly.


Hide 11323C 9.REMOVE NO. 3 TIMING CHAIN COVER

a.
A402701

Using an 8 mm socket wrench, remove the bolt, plate washer and No. 3 timing chain cover from the No. 2 timing chain cover assembly.


Hide 16207 10.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A436616

Slide the clip and disconnect the No. 2 water by-pass pipe sub-assembly from the outlet water by-pass sub-assembly.


b.

Remove the bolt and No. 2 water by-pass pipe sub-assembly.


Hide 16260 11.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

a.
A406737

Remove the bolt to disconnect the flow shutting valve (water by-pass hose assembly).


b.
A406738

Remove the 2 bolts and the water hose clamp bracket.


c.
A406739

Slide the clip and disconnect the flow shutting valve (water by-pass hose assembly) from the water by-pass outlet sub-assembly.

HINT:

Use a container to catch any engine coolant which flows out of the flow shutting valve (water by-pass hose assembly) and water by-pass outlet sub-assembly.



Hide 17167 12.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A404785

Remove the 5 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.


Hide 17141 14.REMOVE EXHAUST MANIFOLD

a.
A404786

Using a 12 mm deep socket wrench, remove the 7 nuts and separate the exhaust manifold from the cylinder head sub-assembly.


b.
A404787

Remove the exhaust manifold to head gasket from the cylinder head sub-assembly.


Hide 22030 15.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 25680 16.REMOVE EGR COOLER ASSEMBLY

a.
A429162C01
2.292,1.344 2.49,1.052 2.49,1.052 2.646,1.052 true 1.104,0.76 1.292,0.542 1.292,0.542 1.469,0.542 true 2.677,0.938 2.917,1.167 0.24,0.229 10 true *1 1.5,0.438 1.698,0.646 0.198,0.208 10 true *2
*1 No. 3 Water By-pass Hose
*2 Water Hose


Slide the clip and disconnect the water hose from the EGR cooler assembly.


b.

Slide the clip and disconnect the No. 3 water by-pass hose from the EGR cooler assembly.


c.
A402703

Remove the 5 bolts, EGR cooler assembly, EGR cooler gasket and EGR valve gasket.


Hide 25687 17.REMOVE NO. 1 EGR COOLER BRACKET

a.
A402704

Remove the 2 bolts and No. 1 EGR cooler bracket from the EGR valve bracket and water outlet.


Hide 25601 18.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

a.
A402705

Using an 8 mm socket wrench, remove the 4 bolts, No. 1 EGR pipe sub-assembly, EGR inlet gasket and EGR valve adapter gasket.


Hide 19.REMOVE NO. 4 WATER BY-PASS HOSE

a.
A428695

Slide the clip and remove the No. 4 water by-pass hose from the EGR valve assembly.


Hide 25620 20.REMOVE EGR VALVE ASSEMBLY

a.
A402706

Disconnect the clamp.


b.

Slide the clip and disconnect the No. 8 water by-pass hose from the EGR valve assembly.


c.
A402707

Using an 8 mm socket wrench, remove the bolt and disconnect the fuel pipe sub-assembly from the EGR valve bracket.


d.

Using an 8 mm socket wrench, remove the bolt.


e.
A406949C01
2.323,0.813 2.51,0.552 2.51,0.552 2.656,0.552 true 2.333,0.938 2.542,0.938 true 2.583,0.854 2.896,1.052 0.313,0.198 10 true *a 2.708,0.448 3.021,0.646 0.313,0.198 10 true *b
*a Pin
*b Hole


Remove the EGR valve assembly vertically.


f.
A402708

Using an 8 mm socket wrench, remove the bolt and EGR valve bracket.


Hide 16279 21.REMOVE NO. 3 WATER BY-PASS PIPE

a.
A402709

Using an 8 mm socket wrench, remove the bolt and No. 3 water by-pass pipe from the intake manifold.


b.

Slide the clip and disconnect the No. 3 water by-pass pipe from the water outlet.


Hide 16278 22.REMOVE NO. 2 WATER BY-PASS PIPE

a.
A402710N02
0.521,1.073 0.677,1.271 0.156,0.198 10 true B 2.073,1.896 2.229,2.094 0.156,0.198 10 true A 1.031,1.927 1.188,2.125 0.156,0.198 10 true B

Remove the bolt (A).


b.

Using an 8 mm socket wrench, remove the 2 bolts (B) and No. 2 water by-pass pipe.


Hide 17177 24.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23901 25.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 23801P 26.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

a.
A407176

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.


Hide 23100X 27.REMOVE FUEL PUMP ASSEMBLY (for High Pressure)

Hide 16295 28.REMOVE NO. 7 WATER BY-PASS HOSE

a.
A402711

Slide the 2 clips and remove the No. 7 water by-pass hose.


Hide 82219A 29.REMOVE SENSOR WIRE

a.
A401308

Disconnect the 4 connectors.


b.

Detach the 3 clamps.


c.

Using an 8 mm socket wrench, remove the bolt and sensor wire from the water inlet with thermostat sub-assembly.


Hide 82126A 30.REMOVE NO. 6 ENGINE WIRE

a.
A401309

Disconnect the 4 connectors.


b.

Detach the 2 clamps.


c.

Remove the 2 nuts and No. 6 engine wire from the wire harness clamp bracket.


Hide 31.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A401310

Using an 8 mm socket wrench, remove the 2 bolts and wire harness clamp bracket from the No. 1 ventilation case.


Hide 23807 32.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23807V 33.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23291 34.REMOVE INJECTOR VIBRATION INSULATOR

Hide 23250F 36.REMOVE PORT FUEL INJECTOR ASSEMBLY

Hide 23250E 38.REMOVE DIRECT FUEL INJECTOR ASSEMBLY

Hide 11452 41.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Remove the engine oil level dipstick.


b.
A400314

Using an 8 mm socket wrench, remove the bolt and engine oil level dipstick guide from the cylinder head sub-assembly.


c.
A400321

Remove the O-ring from the engine oil level dipstick guide.


Hide 17169A 42.REMOVE NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

a.
A402712

Remove the 2 bolts and No. 3 exhaust manifold heat insulator from the cylinder block sub-assembly.


Hide 25861A 44.REMOVE NO. 2 VACUUM SWITCHING VALVE BRACKET

a.
A402205

Using an 8 mm socket wrench, remove the 2 bolts and No. 2 vacuum switching valve bracket from the cylinder head sub-assembly.