Home › Drivetrain › UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE ASSEMBLY
RM3620E _52 Drivetrain _076122 UB80E AUTOMATIC TRANSMISSION / TRANSAXLE _0370676 AUTOMATIC TRANSAXLE ASSEMBLY A

UB80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C374401C01
2.25,0.417 2.625,0.146 2.625,0.146 2.771,0.146 true 0.573,0.448 0.719,0.448 0.719,0.448 0.917,0.885 true 2.813,0.021 3.073,0.219 0.26,0.198 10 false *a 0.354,0.344 0.552,0.542 0.198,0.198 10 true *b
*a Matchmark
*b Key


Set the key at the top of the front oil pump drive gear and put a matchmark on the transaxle housing.


b.
C361055C02
1.479,0.188 1.573,0.188 1.573,0.188 1.74,0.688 false 1.729,1.583 2.167,1.906 false 1.281,0.063 1.594,0.26 0.313,0.198 10 false *a 2.229,1.885 2.542,2.083 0.313,0.198 10 false *b
*a Groove
*b Matchmark
V100135

MP Grease


Apply MP grease to place a matchmark on the torque converter assembly so that the position of its groove is clearly indicated.


c.
C374402C01
1.198,0.76 0.458,0.427 0.458,0.427 1.198,0.646 true 2.219,1.25 1.49,1.969 1.49,1.969 2.219,0.958 true 1.313,1.969 1.552,2.167 0.24,0.198 10 false *1 0.281,0.302 0.542,0.542 0.26,0.24 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Align the matchmark on the housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




d.
C374403C01
1.198,0.635 0.948,0.24 0.948,0.24 0.813,0.24 true 1.198,1.75 0.938,2.073 0.938,2.073 0.802,2.073 true 2.25,1.26 1.625,1.948 1.625,1.948 2.229,0.979 true 0.594,0.135 0.792,0.333 0.198,0.198 10 false *a 0.594,1.969 0.792,2.167 0.198,0.198 10 false *a 1.469,1.948 1.698,2.156 0.229,0.208 10 false *1
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




e.
C374404C01
1.208,0.771 0.719,0.365 0.719,0.365 1.208,0.656 true 2.24,1.271 1.625,1.969 1.625,1.969 2.229,0.979 true 1.458,1.969 1.677,2.177 0.219,0.208 10 false *1 0.51,0.229 0.719,0.427 0.208,0.198 10 false *a
*1 Front Oil Pump Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the housing and insert the groove of the torque converter assembly into the key of the oil pump drive gear.

NOTICE:
·

Do not push the torque converter assembly excessively when rotating it.

·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the front oil pump oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C374406N02
2.375,0.167 2.552,0.406 0.177,0.24 10 false A

Using a vernier caliper and straightedge, measure the dimension (A) shown in the illustration and check the dimension (A).

Standard:

14 mm (0.5512 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the automatic transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C374400

Install the 4 wire harness clamp brackets to the automatic transaxle case sub-assembly and transmission case side cover with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
C374399

Install the wire harness clamp bracket to the automatic transaxle case sub-assembly with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.
C374398

Install the wire harness clamp bracket to the automatic transaxle case sub-assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 35150 3.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

a.

Coat a new O-ring with Toyota Genuine ATF WS and install it to the transmission case plug assembly.


b.

Install the transmission case plug assembly to the transaxle housing.


Hide 33823 4.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the automatic transaxle case sub-assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 33493A 5.INSTALL TRANSMISSION OIL COOLER

Hide 32907C 6.INSTALL NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

Hide 32941 7.CONNECT INLET NO. 1 OIL COOLER HOSE

Hide 32942 8.CONNECT OUTLET NO. 1 OIL COOLER HOSE

Hide 30500 9.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

a.
C363764C01
1.698,1.063 1.927,1.063 false 1.167,1 1.479,1.198 0.313,0.198 10 false *1 1.969,0.979 2.281,1.177 0.313,0.198 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum Grease Amount:

Approximately 1 g (0.0353 oz)



b.
C374407C01
0.698,1.49 0.813,1.49 0.813,1.49 1.115,1.073 true 2.802,0.875 2.656,0.875 2.656,0.875 2.156,0.375 true 0.458,1.385 0.656,1.583 0.198,0.198 10 true *1 2.844,0.74 3.042,0.938 0.198,0.198 10 true *1
*1 Knock Pin


Confirm that the 2 knock pins are installed on the engine assembly and are not damaged.


c.
C374393N01
2.448,0.031 2.604,0.229 0.156,0.198 10 false A 2.865,0.219 3.021,0.417 0.156,0.198 10 false A 1.01,0.042 1.167,0.24 0.156,0.198 10 false B 2.469,1.979 2.625,2.177 0.156,0.198 10 false C 2.823,1.719 2.979,1.917 0.156,0.198 10 false D 1.229,2.01 1.385,2.167 0.156,0.156 10 false D 0.938,1.865 1.073,2.063 0.135,0.198 10 true D 0.771,0.448 0.906,0.646 0.135,0.198 10 false D

While keeping the engine assembly and automatic transaxle assembly horizontal, align the knock pins with the holes in the automatic transaxle assembly and install the automatic transaxle assembly with the 8 bolts shown in the illustration.

Torque:
Bolt (A) : 64 N*m (653 kgf*cm, 47 ft.*lbf)
Bolt (B) : 46 N*m (469 kgf*cm, 34 ft.*lbf)
Bolt (C) : 25 N*m (255 kgf*cm, 18 ft.*lbf)
Bolt (D) : 46 N*m (469 kgf*cm, 34 ft.*lbf)

Bolt Length:
Bolt Length
(A) 50 mm (1.97 in.)
(B) 45 mm (1.77 in.)
(C) 35 mm (1.38 in.)
(D) 45 mm (1.77 in.)


NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excess force when installing the automatic transaxle assembly.

·

When mounting the automatic transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.

·

Check that the torque converter assembly rotates.

·

When tightening the bolts, be sure that the mating surfaces of the engine assembly and the automaitc transaxle assembly are in close contact with one another.




Hide 12303 10.INSTALL REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY

a.
C402766N01
2.219,0.917 2.385,1.083 0.167,0.167 10 false A 2.021,1.917 2.188,2.083 0.167,0.167 10 false B 2.219,1.5 2.385,1.667 0.167,0.167 10 true C 0.75,0.635 0.917,0.802 0.167,0.167 10 true C

Install the rear engine mounting bracket sub-assembly to the transaxle housing with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (A) → Tighten bolt (C)



Hide 12372A 12.INSTALL ENGINE MOUNTING INSULATOR LH

a.
C402765N01
0.625,1.667 0.792,1.833 0.167,0.167 10 true A 2.604,0.677 2.771,0.844 0.167,0.167 10 true B 1.99,0.146 2.156,0.313 0.167,0.167 10 true C 1.792,1.885 1.958,2.052 0.167,0.167 10 true C 0.604,0.76 0.771,0.927 0.167,0.167 10 true D

Install the engine mounting insulator LH to the automatic transaxle case sub-assembly with the 5 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (C) → Tighten bolt (A) → Tighten bolt (D)



Hide 12311A 13.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

a.
C402764N01
1.146,0.135 1.313,0.302 0.167,0.167 10 true A 2.188,1.875 2.354,2.042 0.167,0.167 10 true B 0.833,1.375 1,1.542 0.167,0.167 10 true C

Install the transverse engine engine mounting bracket to the transaxle housing with the 3 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

Tightening order: Temporarily install bolt (A) → Tighten bolt (B) → Tighten bolt (C) → Tighten bolt (A)



Hide 12361 14.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.
C408666

Install the front engine mounting insulator to the transverse engine engine mounting bracket with the bolt.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 20.CONNECT WIRE HARNESS (for RHD)

a.
C402760

Engage the wire harness clamp to connect the wire harness to the automatic transaxle assembly.


b.

Install the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Engage the 8 wire harness clamps to connect the wire harness.

C407373


d.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

Connect the wire harness to the rack and pinion power steering gear assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

C407372


f.

Connect the rack and pinion power steering gear assembly connector.

NOTICE:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.



g.
C402757

Engage the wire harness clamp and connect the vacuum switching valve (for active control engine mount system) connector.


h.
C402756

Connect the park/neutral position switch assembly connector.


i.
C374408

Connect the connector of the transmission wire connector and rotate the lever and engage the claw.

HINT:

Rotate the lever until the claw of the transmission wire connector makes a click sound.



Hide 21.CONNECT WIRE HARNESS (for LHD)

a.
C402760

Engage the wire harness clamp to connect the wire harness to the automatic transaxle assembly.


b.

Install the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Engage the 9 wire harness clamps to connect the wire harness.

C402759


d.

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

Connect the wire harness to the rack and pinion power steering gear assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

C402767


f.

Connect the rack and pinion power steering gear assembly connector.

NOTICE:

Make sure that the connector is fully inserted before rotating the lock lever to engage the lock.



g.
C402757

Engage the wire harness clamp and connect the vacuum switching valve (for active control engine mount system) connector.


h.
C402756

Connect the park/neutral position switch assembly connector.


i.
C402768

Connect the connector of the transmission wire connector and rotate the lever and engage the claw.

HINT:

Rotate the lever until the claw of the transmission wire connector makes a click sound.



Hide 45319 22.INSTALL STEERING GEAR HEAT INSULATOR (for LHD)

Hide 35104V 23.INSTALL BREATHER PLUG HOSE

a.
C364011C01
1.688,0.438 2.24,0.438 false 1.167,1.396 1.719,1.396 false 1.531,0.375 1.844,0.531 0.313,0.156 10 false *1 1,1.323 1.313,1.479 0.313,0.156 10 false *2
*1 Breather Plug Sub-assembly
*2 Breather Plug Hose


Install the breather plug sub-assembly to the breather plug hose.


b.
C402754

Install the breather plug hose to the No. 1 breather plug (ATM).


c.

Engage the 2 hose clamps to connect the breather plug hose.


Hide 16260 24.CONNECT WATER BY-PASS HOSE ASSEMBLY

Hide 16261G 25.INSTALL FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)

Hide 26.CONNECT VACUUM HOSE

a.

Engage the 9 clamps to connect the vacuum hose to the automatic transaxle assembly.

C402752


b.
C402751

Connect the vacuum hose to the vacuum hose connector.


c.
C402750

Connect the vacuum hose to the rear engine mounting insulator.


Hide 32101A 27.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Remove any remaining adhesive from the 6 drive plate and torque converter assembly setting bolts.


b.
P000601C22
1.979,1.177 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

Make sure to install the 6 drive plate and torque converter assembly setting bolts immediately after applying adhesive to prevent foreign matter from attaching to them.



c.
C402749

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

First install the black-colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver-colored drive plate and torque converter assembly setting bolts.



Hide 11361J 28.INSTALL FLYWHEEL HOUSING UNDER COVER

Hide 29.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 30.CHECK AUTOMATIC TRANSAXLE SYSTEM

NOTICE:

If automatic transaxle parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION