Home › Engine / Hybrid System › CRUISE CONTROL › LANE CONTROL SYSTEM
RM3620E _51 Engine / Hybrid System _076038 CRUISE CONTROL _0370841 LANE CONTROL SYSTEM J

CRUISE CONTROL  LANE CONTROL SYSTEM  Indicator Circuit  


DESCRIPTION

The LTA/LDA indicator output request signal is sent from the forward recognition camera to the combination meter assembly via CAN communication.

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, make sure to replace it with a new one. If a device that was installed in another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle, and may cause a DTC to be output.

·

When replacing the forward recognition camera, the forward recognition camera optical axis must be adjusted.

HINT:

Perform forward recognition camera axis alignment with either "One time recognition" or "Sequential Recognition".



·

When replacing the combination meter assembly, be sure to replace it with a new part. If a device that was installed in another vehicle is used, the information stored in the combination meter assembly will not match the information from the vehicle, and may cause a DTC to be output.



PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / CAN Bus Check.

CAN Bus Check
50007

Result:
Result Proceed to
CAN communication system is normal (DTC (CAN Communication Malfunction, ECU Communication Malfunction/Communication Lost) is not output) A
CAN communication system is malfunctioning (DTC (CAN Communication Malfunction, ECU Communication Malfunction/Communication Lost) is output) B



A

2.CHECK FOR DTC (HEALTH CHECK)

B

2.CHECK FOR DTC (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check DTCs.


f.

Turn the ignition switch off.


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

3.PERFORM ACTIVE TEST USING GTS (METER DISPLAY (ALL))

B

GO TO FLOWCHART OF DTC

3.PERFORM ACTIVE TEST USING GTS (METER DISPLAY (ALL))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

According to the display on the GTS, perform the Active Test.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Meter Display (All) Multi-information display ON Confirm that the vehicle is stopped with the ignition switch to ON.
Body Electrical > Combination Meter > Active Test
Tester Display
Meter Display (All)
50004 409 277

f.

Turn the ignition switch off.


Result:
Result Proceed to
The multi-information display in the combination meter assembly turns on according to the Active Test A
The multi-information display in the combination meter assembly does not turn off according to the Active Test B



A

4.READ VALUE USING GTS (LDA CONTROL)

B

REPLACE COMBINATION METER ASSEMBLY

4.READ VALUE USING GTS (LDA CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Land Control / Data List.


e.

Read the Data List according to the display on the GTS.

Chassis > Lane Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
LDA Control Control status of lane control system Prohibit or Permit Prohibit: Lane control system prohibited
Permit: Lane control system permitted
Confirm that the vehicle is stopped with the ignition switch to ON.
Chassis > Lane Control > Data List
Tester Display
LDA Control
50003 418 3

Result:
Result Proceed to
Data List value changes and LTA/LDA indicator light turns on when LTA/LDA main switch is operated A
Data List value changes but LTA/LDA indicator light does not turn on when LTA/LDA main switch is operated B
Data List value does not change and LTA/LDA indicator light does not turn on when LTA/LDA main switch is operated C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE COMBINATION METER ASSEMBLY

C

REPLACE FORWARD RECOGNITION CAMERA