The No. 1 air conditioning radiator damper servo sub-assembly (driver side mode) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the No. 1 air conditioning radiator damper servo sub-assembly (driver side mode) to the appropriate position, which controls the air outlet switching.
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.
| DTC No. | Detection Item | DTC Diagnosis Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1443 | Air Outlet Damper Control Servo Motor Circuit | ·
Diagnosis condition: During No. 1 air conditioning radiator damper servo sub-assembly (driver side mode) operation ·
Malfunction status: The damper servo operation request signal is output but the position information of the servo does not change or servo is malfunctioning ·
Detection time: Continuously for 30 seconds or more |
·
No. 1 air conditioning radiator damper servo sub-assembly (driver side mode) ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
Memorized |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | During No. 1 air conditioning radiator damper servo sub-assembly (driver side mode) operation | ○ | ○ |
| Malfunction Status | The damper servo operation request signal is output but the position information of the servo does not change | ○ | - |
| The damper servo operation request signal is output but the position information of the servo is malfunctioning | - | ○ | |
| Detection Time | Continuously for 30 seconds or more | Continuously for 30 seconds or more | |
| Trip Count | 1 trip | 1 trip | |
If the conditions match either of these patterns, a DTC will be output.
When DTC B1441, B1442, B1443 and B1446 are output at the same time, the No. 1 air conditioning radiator damper servo sub-assembly is malfunctioning.
Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.
When installing the servo motor, make sure to install it correctly.
When the servo motor is replaced, be sure to perform servo motor initialization.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>INITIALIZATION
Check for DTCs.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for HV Model)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B1443 is output | A |
| DTC B1443 and B1497 are output | B |
A
B
Check that the No. 1 air conditioning radiator damper servo sub-assembly is installed correctly.
No. 1 air conditioning radiator damper servo sub-assembly is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for A25A-FXS)>REASSEMBLY
Check for a wire harness caught between the links of the motors and dampers.
No wire harnesses are caught between the links of the motors and dampers.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 air conditioning radiator damper servo sub-assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for A25A-FXS)>DISASSEMBLY
Operate the dampers by hand.
The dampers are easily operated by hand.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for A25A-FXS)>DISASSEMBLY
NG