Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Front)
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370876 ULTRASONIC SENSOR(for Front) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Front)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89305 1.INSTALL ULTRASONIC SENSOR CUSHION SET (w/ Parking Support Brake System)

HINT:

Only perform this procedure when removing and installing the ultrasonic sensor cushion set.


a.

Install the ultrasonic sensor cushion set as shown in the illustration.

B549652C01
0,0 0,0 false
V113147

Install in this Direction - -



Hide 89347B 2.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (except Off Road Package)

NOTICE:
·

Installing the front corner ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.



HINT:

Perform the following procedure only when replacement of a front corner ultrasonic sensor retainer is necessary.


a.

Clean the front bumper assembly surface.

i.

Remove any remaining double-sided tape from the front bumper assembly.


ii.

Wipe off any tape adhesive residue with cleaner.



b.
B502899C04
2.604,1.146 2.917,1.344 0.313,0.198 10 false *a 1.49,0.156 1.802,0.354 0.313,0.198 10 false *a
*a 30 mm (1.18 in.)


Cover the sensor installation hole from the outside of the front bumper cover with a 30 mm (1.18 in.) square piece of tape.


c.

Apply primer to the front bumper assembly on the installation area of the front corner ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the front corner ultrasonic sensor retainer has been attached.



B525242C01
2,1.5 2,1.25 false 5,1.563 5,1.313 false 0.104,0.083 0.417,0.323 0.313,0.24 12 false *A 3.521,0.094 3.833,0.333 0.313,0.24 12 false *B 1.917,1.51 2.229,1.667 0.313,0.156 10 false *a 4.938,1.573 5.25,1.729 0.313,0.156 10 false *a
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
*a Scribed Line - -
V100145

Primer Application - -



d.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



e.

Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.


f.

Remove the peeling paper of the new front corner ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



g.

Align the front corner ultrasonic sensor retainer with the scribed line on the front bumper assembly and install it as shown in the illustration.

NOTICE:

The application strength of the front corner ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Apply pressure so that it does not lift up from the front bumper assembly.

·

Pushing force: 50 N (5.1 kgf) for 3 seconds



B525240C01
1.969,1.521 1.969,1.271 false 5.198,1.563 5.198,1.313 false 0.104,0.094 0.417,0.333 0.313,0.24 12 false *A 3.604,0.083 3.917,0.323 0.313,0.24 12 false *B 1.906,1.552 2.156,1.75 0.25,0.198 10 true *a 5.115,1.552 5.365,1.75 0.25,0.198 10 true *a
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
*a Scribed Line - -



Hide 89347B 3.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (for Off Road Package)

NOTICE:
·

Installing the front corner ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.



HINT:

Perform the following procedure only when replacement of a front corner ultrasonic sensor retainer is necessary.


a.

Clean the front bumper assembly surface.

i.

Remove any remaining double-sided tape from the front bumper assembly.


ii.

Wipe off any tape adhesive residue with cleaner.



b.
B502899C04
2.604,1.146 2.917,1.344 0.313,0.198 10 false *a 1.49,0.156 1.802,0.354 0.313,0.198 10 false *a
*a 30 mm (1.18 in.)


Cover the sensor installation hole from the outside of the front bumper cover with a 30 mm (1.18 in.) square piece of tape.


c.
B525418C01
1.833,1.896 1.833,1.646 false 1.771,1.927 2.083,2.083 0.313,0.156 10 false *a
*a Scribed Line
V100145

Primer Application


Apply primer to the front bumper assembly on the installation area of the front corner ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the front corner ultrasonic sensor retainer has been attached.




d.

Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))



e.

Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.


f.

Remove the peeling paper of the new front corner ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



g.
B525419C01
1.719,1.865 1.719,1.531 true 1.625,1.896 1.844,2.115 0.219,0.219 10 true *a
*a Scribed Line


Align the front corner ultrasonic sensor retainer with the scribed line on the front bumper assembly and install it as shown in the illustration.

NOTICE:

The application strength of the front corner ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.


HINT:
·

Apply pressure so that it does not lift up from the front bumper assembly.

·

Pushing force: 50 N (5.1 kgf) for 3 seconds




Hide 89341L 4.INSTALL FRONT CENTER ULTRASONIC SENSOR (except Off Road Package)

a.

Attach the claw to install the front center ultrasonic sensor.

NOTICE:
·

When reusing the sensor, make sure that each sensor is returned to its original position.

·

Check that the claw is securely fitted.

·
B494879C08
0,0 0,0 false
V100155

Microphone Surface


Do not push the microphone surface.



B525233C01
0.083,0.083 0.417,0.333 0.333,0.25 12 false *A 3.5,0.083 3.833,0.333 0.333,0.25 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
V113147

Install in this Direction - -



b.

Connect the connector.

B525231C02
0.083,0.083 0.417,0.333 0.333,0.25 12 false *A 3.5,0.094 3.813,0.333 0.313,0.24 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System



Hide 89341L 5.INSTALL FRONT CENTER ULTRASONIC SENSOR (for Off Road Package)

a.
B525420C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the front center ultrasonic sensor.

NOTICE:
·

When reusing the sensor, make sure that each sensor is returned to its original position.

·

Check that the claw is securely fitted.

·
B494879C08
0,0 0,0 false
V100155

Microphone Surface


Do not push the microphone surface.




b.
B525415

Connect the connector.


Hide 89341K 6.INSTALL FRONT CORNER ULTRASONIC SENSOR (except Off Road Package)

a.

Attach the claw to install the front corner ultrasonic sensor.

NOTICE:
·

When reusing the sensor, make sure that each sensor is returned to its original position.

·

Check that the claw is securely fitted.

·
B494879C09
0,0 0,0 false
V100155

Microphone Surface


Do not push the microphone surface.



HINT:

w/ Parking Support Brake System:

Align the connector with the protrusion of the mark when connecting it.


B525244C01
6,1.083 6,0.917 false 0.083,0.083 0.417,0.323 0.333,0.24 12 false *A 3.604,0.094 3.917,0.333 0.313,0.24 12 false *B 5.938,1.094 6.25,1.292 0.313,0.198 10 false *a
*A w/o Parking Support Brake System *B w/ Parking Support Brake System
*a Protrusion of the mark - -
V113147

Install in this Direction - -



b.

Connect the connector.

B525236C02
0.083,0.083 0.417,0.323 0.333,0.24 12 false *A 3.5,0.094 3.813,0.333 0.313,0.24 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System



Hide 89341K 7.INSTALL FRONT CORNER ULTRASONIC SENSOR (for Off Road Package)

a.
B525421C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the front corner ultrasonic sensor.

NOTICE:
·

When reusing the sensor, make sure that each sensor is returned to its original position.

·

Check that the claw is securely fitted.

·
B494879C09
0,0 0,0 false
V100155

Microphone Surface


Do not push the microphone surface.




b.
B525413

Connect the connector.


Hide 89348X 8.INSTALL FRONT ULTRASONIC SENSOR CLIP (except Off Road Package)

a.

Attach the wire harness clamp.

B525235C02
0.104,0.083 0.417,0.323 0.313,0.24 12 false *A 3.583,0.083 3.896,0.333 0.313,0.25 12 false *B
*A w/o Parking Support Brake System *B w/ Parking Support Brake System



b.
B525245C02
0,0 0,0 false
V113146

Pushing here
V113147

Install in this Direction


w/o Parking Support Brake System:

While pushing the positions shown in the illustration, attach the claw to install the front ultrasonic sensor clip.


c.
B525246C01
0,0 0,0 false
V113147

Install in this Direction


w/ Parking Support Brake System:

Attach the claw to install the front ultrasonic sensor clip.


Hide 86790B 10.ADJUST FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)