Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Gasoline Model)
RM3620E _58 Vehicle Interior _076130 HEATING / AIR CONDITIONING _0370843 AIR CONDITIONING SYSTEM(for Gasoline Model) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Gasoline Model)  B1442  Air Inlet Damper Control Servo Motor Circuit  


DESCRIPTION

The No. 1 blower damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the No. 1 blower damper servo sub-assembly to the appropriate position, which controls the air inlet mode (fresh, recirculation/fresh, and recirculation).

The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1442 Air Inlet Damper Control Servo Motor Circuit
·

Diagnosis condition: During No. 1 blower damper servo sub-assembly operation

·

Malfunction status: The damper servo operation request signal is output but the position information of the servo does not change or servo is malfunctioning

·

Detection time: Continuously for 30 seconds or more


·

No. 1 blower damper servo sub-assembly

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly


Memorized

DTC Detection Condition Combination Table
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition During No. 1 blower damper servo sub-assembly operation ○ ○
Malfunction Status The damper servo operation request signal is output but the position information of the servo does not change ○ -
The damper servo operation request signal is output but the position information of the servo is malfunctioning - ○
Detection Time Continuously for 30 seconds or more Continuously for 30 seconds or more
Trip Count 1 trip 1 trip

HINT:

If the conditions match either of these patterns, a DTC will be output.


WIRING DIAGRAM

E396770E04
5.042,0.708 5.813,0.906 0.771,0.198 10 false BUS 5.042,1.094 5.813,1.292 0.771,0.198 10 false B BUS 5.052,1.49 5.823,1.688 0.771,0.198 10 false BUS G 4.76,0.677 5.01,0.875 0.25,0.198 10 false 3 4.76,1.104 5.01,1.302 0.25,0.198 10 false 4 4.771,1.479 5.021,1.677 0.25,0.198 10 false 2 1.042,0.75 1.75,1.188 0.708,0.438 10 false Driver Side Air Mix*1 0.74,3.938 1.844,4.156 1.104,0.219 10 false Driver Side Mode 0.771,4.896 2.688,5.563 1.917,0.667 10 false No. 1 Air Conditioning Radiator Damper Servo Sub-assembly 0.875,7.5 2.573,8 1.698,0.5 10 false No. 1 Blower Damper Servo Sub-assembly 3.156,7.438 4.698,7.875 1.542,0.438 10 false Air Conditioning Harness Assembly 4.729,8.083 5.5,8.281 0.771,0.198 10 false z11 4.719,8.25 6.99,8.5 2.271,0.25 10 false Air Conditioning Amplifier Assembly 0.885,8.563 3.26,8.823 2.375,0.26 10 false : LIN Communication Line 6.021,0.823 6.792,1.021 0.771,0.198 10 false IC 6.333,0.938 7.104,1.135 0.771,0.198 10 false +B 0.75,2.448 1.823,2.802 1.073,0.354 10 false Front Passenger Side Air Mix*1 0.167,8.031 3.219,8.313 3.052,0.281 10 false *1: for Automatic Air Conditioning System 1.146,1.438 1.833,1.635 0.688,0.198 10 false Air Mix*2 0.177,8.302 3.229,8.583 3.052,0.281 10 false *2: for Manual Air Conditioning System

CAUTION / NOTICE / HINT

NOTICE:
·

When DTC B1441, B1442, B1443 and B1446 are output at the same time, the No. 1 air conditioning radiator damper servo sub-assembly is malfunctioning (for Automatic Air Conditioning System).

·

When DTC B1441, B1442 and B1443 are output at the same time, the No. 1 air conditioning radiator damper servo sub-assembly is malfunctioning (for Manual Air Conditioning System).

·

Confirm that no mechanical problem is present because this diagnostic code can be output when either a damper link or the damper is mechanically locked.

·

When installing the servo motor, make sure to install it correctly.

·

When the servo motor is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Gasoline Model)>INITIALIZATION



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Gasoline Model)>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTC B1442 is output A
DTC B1442 and B1497 are output B



A

2.CHECK NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY

B

2.CHECK NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY
a.

Check that the No. 1 blower damper servo sub-assembly is installed correctly.

OK:

No. 1 blower damper servo sub-assembly is installed correctly.



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (MOTOR, LINK, DAMPER)

NG

REINSTALL NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY

3.CHECK NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY (MOTOR, LINK, DAMPER)
a.

Check for a wire harness caught between the links of the motors and dampers.

OK:

No wire harnesses are caught between the links of the motors and dampers.



Result:
Proceed to
OK
NG



OK

4.CHECK BLOWER ASSEMBLY (DAMPER)

NG

REMOVE PINCHED WIRE HARNESS

4.CHECK BLOWER ASSEMBLY (DAMPER)
a.

Remove the No. 1 blower damper servo sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY


b.

Operate the dampers by hand.

OK:

The dampers are easily operated by hand.



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY

NG

REPAIR OR REPLACE BLOWER ASSEMBLY