Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370833 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB3  Short to GND in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a short to ground in the outer rear view mirror indicator RH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB3 Short to GND in Outer Mirror Indicator(Slave)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The current that is sent from the blind spot monitor sensor to the indicator is above a specified level for a specified period of time


·

Outer mirror RH (outer rear view mirror indicator RH)

·

Outer rear view mirror assembly RH

·

Harness or connector

·

Blind spot monitor sensor RH



WIRING DIAGRAM

E270468E41
3.125,1.417 3.281,1.615 0.156,0.198 10 false 2 3.167,1.823 3.323,2.021 0.156,0.198 10 false 1 2.844,1.563 3,1.76 0.156,0.198 10 false + 2.802,1.948 2.958,2.146 0.156,0.198 10 false - 1.146,2.396 1.802,2.625 0.656,0.229 10 false IND2 1.167,2.625 2.885,3.021 1.719,0.396 10 false Outer Mirror RH (Outer Rear View Mirror Indicator RH) 0.438,3.708 2.771,4.104 2.333,0.396 10 false Outer Rear View Mirror Assembly RH 3.438,1.448 3.906,1.646 0.469,0.198 10 false BSR+ 5.479,1.604 5.948,1.802 0.469,0.198 10 false OMIR 5.177,1.479 5.646,1.677 0.469,0.198 10 false 4 5.365,3.563 5.833,3.76 0.469,0.198 10 false Q13 5.354,3.75 6.583,4.375 1.229,0.625 10 false Blind Spot Monitor Sensor RH 3.885,1.458 4.115,1.646 0.229,0.188 10 false 13 3.885,1.854 4.156,2.021 0.271,0.167 10 false 10 3.594,1.875 3.833,2.042 0.24,0.167 10 false - 0.458,3.563 0.927,3.76 0.469,0.198 10 false I13

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR ASSEMBLY RH)
2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.
E406932C14
1.5,0.25 1.875,0.542 0.375,0.292 1.875,1.146 2.385,0.51 2.385,0.51 2.583,0.51 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.563,0.323 1.875,0.521 0.313,0.198 10 false Q13 2.667,0.427 3.073,0.615 0.406,0.188 10 false OMIR
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Disconnect the blind spot monitor sensor RH connector.


b.

Disconnect the I13 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q13-4 (OMIR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.
E395851C05
0.229,0.938 0.594,1.25 0.365,0.313 2.125,1.844 1.958,1.844 1.958,1.844 1.75,1.354 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 0.313,1.01 0.625,1.208 0.313,0.198 10 false I13 2.188,1.781 2.677,1.969 0.49,0.188 10 false BSR+
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the IND2 outer mirror RH (outer rear view mirror indicator RH).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I13-13 (BSR+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

4.INSPECT OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)
a.

Remove the outer mirror RH (outer rear view mirror indicator RH).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL


b.

Inspect the outer mirror RH (outer rear view mirror indicator RH).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE OUTER MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH)