Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM3620E _56 Audio / Visual / Telematics _076129 PARK ASSIST / MONITORING _0370833 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB4  Open in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects an open in the outer rear view mirror indicator LH.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1AB4 Open in Outer Mirror Indicator(Master)
Both of the following conditions are met:
·

The blind spot monitor system is on


·

The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator


·

Outer mirror LH (outer rear view mirror indicator LH)

·

Outer rear view mirror assembly LH

·

Harness or connector

·

Blind spot monitor sensor LH



WIRING DIAGRAM

E270468E40
3.073,1.458 3.229,1.656 0.156,0.198 10 false 2 3.094,1.896 3.365,2.104 0.271,0.208 10 false 1 2.813,1.625 2.969,1.823 0.156,0.198 10 false + 2.802,2.021 2.958,2.219 0.156,0.198 10 false - 0.76,2.427 1.417,2.656 0.656,0.229 10 false IND1 0.75,2.635 3.208,2.979 2.458,0.344 10 false Outer Mirror LH (Outer Rear View Mirror Indicator LH) 0.479,3.74 2.958,4.031 2.479,0.292 10 false Outer Rear View Mirror Assembly LH 5.448,1.625 5.917,1.823 0.469,0.198 10 false OMIL 5.188,1.469 5.656,1.667 0.469,0.198 10 false 4 5.313,3.563 5.781,3.76 0.469,0.198 10 false Q1 5.313,3.75 6.521,4.365 1.208,0.615 10 false Blind Spot Monitor Sensor LH 0.458,3.552 0.875,3.74 0.417,0.188 10 false J13 3.427,1.458 3.823,1.625 0.396,0.167 10 false BSL+ 3.646,1.896 3.906,2.083 0.26,0.188 10 false - 3.906,1.448 4.198,1.615 0.292,0.167 10 false 13 3.917,1.844 4.208,2.01 0.292,0.167 10 false 10

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Turn the ignition switch to ON.


c.

Recheck for DTCs and check if the same DTC is output again.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR

Body Electrical > Blind Spot Monitor Master > Trouble Codes
50001 313
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH AND BODY GROUND)
a.

Disconnect the Q1 blind spot monitor sensor LH connector.


b.

Disconnect the J13 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q1-4 (OMIL) - J13-13 (BSL+) Always Below 1 Ω
J13-10 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Disconnect the IND1 outer mirror LH (outer rear view mirror indicator LH) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J13-13 (BSL+) - IND1-2 (+) Always Below 1 Ω
J13-10 (-) - IND1-1 (-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

4.INSPECT OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)
a.

Remove the outer mirror LH (outer rear view mirror indicator LH).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL


b.

Inspect the outer mirror LH (outer rear view mirror indicator LH).

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE OUTER MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH)