Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Clearance Warning ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Clearance Warning ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Clearance Warning (Clearance Sonar)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Clearance Warning (Clearance Sonar)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Clearance Warning (Clearance Sonar)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Clearance Warning ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Clearance warning ECU assembly branch wire or connector

·

Power source circuit of clearance warning ECU assembly

·

Clearance warning ECU assembly ground circuit

·

Clearance warning ECU assembly



WIRING DIAGRAM

C393549E10
5.271,4.198 6.5,4.531 1.229,0.333 10 false Clearance Warning ECU Assembly 5.292,4.021 6.365,4.219 1.073,0.198 10 false H4*1, G25*2 5.594,3.479 5.969,3.656 0.375,0.177 10 false E 5.604,2.344 5.979,2.521 0.375,0.177 10 false IG 5.615,0.5 6.073,0.698 0.458,0.198 10 false R1 5.604,1.094 6.063,1.292 0.458,0.198 10 false R2 5.344,0.417 5.625,0.635 0.281,0.219 10 false 17 5.333,0.979 5.573,1.156 0.24,0.177 10 false 18 4.833,3.344 5.594,3.552 0.76,0.208 10 false 28*5, 30*6 5.385,2.25 5.656,2.458 0.271,0.208 10 false 1 3.333,2.771 4.563,2.969 1.229,0.198 10 false ECU-IG1 NO.4*4 1.573,2.969 3.146,3.219 1.573,0.25 10 false from IG1 NO.1 Relay*4 0.344,1.427 2.458,1.677 2.115,0.25 10 false No. 12 CAN Junction Connector 0.323,1.25 0.719,1.438 0.396,0.188 10 false G102 1.802,0.406 1.99,0.583 0.188,0.177 10 false 7 1.802,0.948 2.104,1.208 0.302,0.26 10 false 17 0.25,3.729 2.938,3.948 2.688,0.219 10 false *2: for LHD and Manual Transaxle 0.24,3.406 3.063,3.677 2.823,0.271 10 false *1: except LHD and Manual Transaxle 0.875,2.427 3.146,2.719 2.271,0.292 10 false from Engine Stop and Start ECU*3 3.677,2.281 4.208,2.479 0.531,0.198 10 false *1, *3 4.594,2.708 4.875,2.875 0.281,0.167 10 false *4 0.26,4.021 2.948,4.24 2.688,0.219 10 false *3: w/ Stop and Start System 0.24,4.313 2.927,4.531 2.688,0.219 10 false *4: w/o Stop and Start System 2.24,4.052 4.927,4.271 2.688,0.219 10 false *5: w/ Parking Support Brake System 2.24,4.344 4.927,4.563 2.688,0.219 10 false *6: w/o Parking Support Brake System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369149C52
1.5,0.604 1.917,0.854 0.417,0.25 1.5,0.25 1.917,0.5 0.417,0.25 2.5,1 2.667,1 2.667,1 3.01,1.604 true 2.583,0.833 2.75,0.833 2.75,0.833 3.167,1.583 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 2.313,0.938 2.625,1.135 0.313,0.198 10 false R1 2.406,0.76 2.719,0.958 0.313,0.198 10 false R2 1.625,0.656 1.938,0.854 0.313,0.198 10 false H4 1.573,0.302 1.906,0.5 0.333,0.198 10 false G25 1.969,0.313 2.281,0.51 0.313,0.198 10 false *A 1.969,0.667 2.281,0.865 0.313,0.198 10 false *B
*A for LHD and Manual Transaxle
*B except LHD and Manual Transaxle
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Disconnect the clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD and Manual Transaxle
Tester Connection Condition Specified Condition
G25-17 (R1) - G25-18 (R2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

except LHD and Manual Transaxle
Tester Connection Condition Specified Condition
H4-17 (R1) - H4-18 (R2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/ Stop and Start System) A
OK (w/o Stop and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

C

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C369149C50
1.5,0.615 1.917,0.865 0.417,0.25 1.375,2.563 1.542,2.563 1.542,2.563 1.542,1.813 true 0.427,0.667 0.26,0.667 0.26,0.667 0.26,1.583 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.208,2.479 1.521,2.677 0.313,0.198 10 false E 0.469,0.583 0.781,0.781 0.313,0.198 10 false IG 1.615,0.656 1.927,0.854 0.313,0.198 10 false H4
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H4-28 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H4-1 (IG) - Body ground Ignition switch ON 10.5 to 16 V
Ignition switch off Below 1 V



Result:
Result Proceed to
OK A
NG (IG terminal) B
NG (Other terminal) C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C369149C51
1.5,0.26 1.917,0.51 0.417,0.25 1.5,0.615 1.917,0.865 0.417,0.25 1.385,2.396 1.552,2.396 1.552,2.396 1.552,1.813 true 0.427,0.667 0.26,0.667 0.26,0.667 0.26,1.583 true 1.615,2.583 1.781,2.583 1.781,2.583 1.781,1.833 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.083,2.323 1.479,2.531 0.396,0.208 10 false E*C 0.469,0.583 0.781,0.781 0.313,0.198 10 false IG 1.615,0.656 1.927,0.854 0.313,0.198 10 false H4 1.583,0.292 1.917,0.49 0.333,0.198 10 false G25 1.969,0.323 2.281,0.521 0.313,0.198 10 false *A 1.969,0.667 2.281,0.865 0.313,0.198 10 false *B 1.323,2.521 1.719,2.729 0.396,0.208 10 false E*D
*A for LHD and Manual Transaxle
*B except LHD and Manual Transaxle
*C w/ Parking Support Brake System
*D w/o Parking Support Brake System
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD and Manual Transaxle
Tester Connection Condition Specified Condition
G25-30 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω

except LHD and Manual Transaxle
Tester Connection Condition Specified Condition
H4-28 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
H4-30 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD and Manual Transaxle
Tester Connection Switch Condition Specified Condition
G25-1 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V

except LHD and Manual Transaxle
Tester Connection Switch Condition Specified Condition
H4-1 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR