Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Radio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Radio Receiver Assembly Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Display and Navigation (AVN)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Display and Navigation (AVN)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Display and Navigation (AVN)" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Radio Receiver Assembly Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Radio and display receiver assembly branch wire or connector

·

Power source circuit of radio and display receiver assembly

·

Radio and display receiver assembly ground circuit

·

Radio and display receiver assembly



WIRING DIAGRAM

C405928E01
5.51,5.042 6.802,5.771 1.292,0.729 10 false Radio and Display Receiver Assembly 5.688,0.427 6.302,0.625 0.615,0.198 10 false CANH 5.677,0.938 6.292,1.135 0.615,0.198 10 false CANL 5.646,1.854 6.26,2.052 0.615,0.198 10 false +B1 5.635,4.635 6.25,4.833 0.615,0.198 10 false GND1 5.667,4.135 6.281,4.333 0.615,0.198 10 false IG 5.656,2.99 6.271,3.188 0.615,0.198 10 false ACC1 5.281,0.406 5.896,0.604 0.615,0.198 10 false G2 5.281,0.938 5.896,1.135 0.615,0.198 10 false G2 5.292,1.854 5.906,2.052 0.615,0.198 10 false G3 5.292,2.979 5.906,3.177 0.615,0.198 10 false G3 5.292,4.125 5.906,4.323 0.615,0.198 10 false G2 5.281,4.635 5.896,4.833 0.615,0.198 10 false G3 5.292,0.208 5.552,0.406 0.26,0.198 10 false 13 5.333,4.417 5.49,4.615 0.156,0.198 10 false 1 5.313,3.917 5.615,4.125 0.302,0.208 10 false 19 5.302,2.771 5.594,2.969 0.292,0.198 10 false 15 5.333,1.656 5.49,1.854 0.156,0.198 10 false 4 5.302,0.729 5.542,0.927 0.24,0.198 10 false 14 1.563,0.302 1.865,0.521 0.302,0.219 10 false 5 1.563,0.802 1.771,1 0.208,0.198 10 false 16 0.125,1.344 2.458,1.698 2.333,0.354 10 false No. 5 CAN Junction Connector 0.115,1.188 0.729,1.385 0.615,0.198 10 false G105 3.396,1.719 4.281,2.125 0.885,0.406 10 false RADIO*2 3.323,2.813 4.271,3.146 0.948,0.333 10 false ECU-ACC*2 3.25,3.948 4.365,4.292 1.115,0.344 10 false ECU-IG1 NO.4 1.417,1.865 2.417,2.417 1,0.552 10 false from Battery*2 1.198,2.99 2.49,3.302 1.292,0.313 10 false from ACC Relay*2 1.052,4.115 2.656,4.438 1.604,0.323 10 false from IG1 NO.1 Relay 0.677,2.406 2.365,2.958 1.688,0.552 10 false from Engine Stop and Start ECU*1 0.677,3.542 2.365,4.094 1.688,0.552 10 false from Engine Stop and Start ECU*1 3.594,2.302 3.833,2.5 0.24,0.198 10 false *1 3.563,3.417 3.802,3.615 0.24,0.198 10 false *1 4.313,2.854 4.552,3.052 0.24,0.198 10 false *2 4.271,1.76 4.51,1.958 0.24,0.198 10 false *2 0.344,4.958 3.021,5.344 2.677,0.385 10 false *1: w/ Stop and Start System 0.354,5.302 3.031,5.688 2.677,0.385 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM


·

The following malfunctions may occur if a radio and display receiver assembly from another vehicle is installed to this vehicle. Therefore, when replacing the radio receiver assembly, be sure to replace it with new one.

-

Communication malfunction DTC is output

-

Does not operate normally




HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369143C35
1.5,0.417 1.917,0.667 0.417,0.25 1.885,2.177 1.583,1.167 1.583,1.167 1.417,1.167 true 2.042,2.167 1.75,1 1.75,1 1.583,1 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.625,0.458 1.938,0.656 0.313,0.198 10 false G2 1.021,1.104 1.51,1.302 0.49,0.198 10 false CANH 1.188,0.938 1.677,1.135 0.49,0.198 10 false CANL
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G2-13 (CANH) - G2-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result Proceed to
OK (w/ Stop and Start System) A
OK (w/o Stop and Start System) B
NG C



A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

C

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the radio and display receiver assembly connector.

C371295C46
1.938,0.094 2.302,0.302 0.365,0.208 5.167,0.063 5.531,0.271 0.365,0.208 3.042,0.76 3.25,0.417 3.25,0.417 3.417,0.417 true 2.927,0.948 3.302,0.781 3.302,0.781 3.469,0.781 true 1.417,0.76 1.167,0.5 1.167,0.5 1,0.5 true 4.594,1.104 4.344,1.271 4.344,1.271 4.177,1.271 true 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 2.042,0.125 2.354,0.323 0.313,0.198 10 false G3 5.271,0.094 5.583,0.292 0.313,0.198 10 false G2 3.479,0.344 3.792,0.542 0.313,0.198 10 false +B1 3.531,0.729 4,0.917 0.469,0.188 10 false ACC1 0.563,0.427 1.031,0.615 0.469,0.188 10 false GND1 4.01,1.208 4.479,1.396 0.469,0.188 10 false IG
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G3-1 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G3-4 (+B1) - Body ground Always 11 to 14 V
G3-15 (ACC1) - Body ground Ignition switch ACC 10.5 to 16 V
Ignition switch off Below 1 V
G2-19 (IG) - Body ground Ignition switch ON 10.5 to 16 V
Ignition switch off Below 1 V



Result:
Result Proceed to
OK A
NG (+B1, ACC1 terminal) B
NG (Other terminal) C



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the radio and display receiver assembly connector.

C371295C46
1.938,0.094 2.302,0.302 0.365,0.208 5.167,0.063 5.531,0.271 0.365,0.208 3.042,0.76 3.25,0.417 3.25,0.417 3.417,0.417 true 2.927,0.948 3.302,0.781 3.302,0.781 3.469,0.781 true 1.417,0.76 1.167,0.5 1.167,0.5 1,0.5 true 4.594,1.104 4.344,1.271 4.344,1.271 4.177,1.271 true 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 2.042,0.125 2.354,0.323 0.313,0.198 10 false G3 5.271,0.094 5.583,0.292 0.313,0.198 10 false G2 3.479,0.344 3.792,0.542 0.313,0.198 10 false +B1 3.531,0.729 4,0.917 0.469,0.188 10 false ACC1 0.563,0.427 1.031,0.615 0.469,0.188 10 false GND1 4.01,1.208 4.479,1.396 0.469,0.188 10 false IG
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G3-1 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G3-4 (+B1) - Body ground Always 11 to 14 V
G3-15 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
G2-19 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR