Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Rear Television Camera Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Rear Television Camera Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Parking Assist Monitor System / Rear Camera" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Parking Assist Monitor System / Rear Camera" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Parking Assist Monitor System / Rear Camera" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Rear Television Camera Communication Stop Mode" in "DTC Combination Table" are output.

Click here


·

Television camera assembly branch wire or connector

·

Power source circuit of television camera assembly

·

Television camera assembly ground circuit

·

Television camera assembly



WIRING DIAGRAM

w/ Panoramic View Monitor System:
C382790E08
0.229,1.625 0.844,1.823 0.615,0.198 10 false N53 0.219,1.792 2.479,2.281 2.26,0.49 10 false No. 8 CAN Junction Connector 1.688,1.281 2.302,1.479 0.615,0.198 10 false 9 1.698,0.813 2.313,1.01 0.615,0.198 10 false 3 5.656,0.906 6.271,1.104 0.615,0.198 10 false CANH 5.667,1.365 6.281,1.563 0.615,0.198 10 false CANL 5.427,1.26 6.042,1.458 0.615,0.198 10 false 1 5.438,0.781 6.052,0.979 0.615,0.198 10 false 4 5.646,2.938 6.26,3.135 0.615,0.198 10 false CB+ 5.667,3.51 6.281,3.708 0.615,0.198 10 false CGND 5.417,3.396 6.031,3.594 0.615,0.198 10 false 5 5.427,2.802 6.042,3 0.615,0.198 10 false 6 5.354,3.958 5.969,4.156 0.615,0.198 10 false R15 5.354,4.104 7.156,4.521 1.802,0.417 10 false Television Camera Assembly 0.292,3.75 0.906,3.948 0.615,0.198 10 false N24 0.292,3.917 2.167,4.24 1.875,0.323 10 false Parking Assist ECU 1.198,3.521 1.813,3.719 0.615,0.198 10 false CGND 1.302,2.948 1.917,3.146 0.615,0.198 10 false CB+ 1.698,2.813 2.313,3.01 0.615,0.198 10 false 33 1.729,3.354 2.344,3.552 0.615,0.198 10 false 32

w/ Parking Assist Monitor System:
C382790E16
0.229,1.625 0.844,1.823 0.615,0.198 10 false N53 0.219,1.792 2.479,2.281 2.26,0.49 10 false No. 8 CAN Junction Connector 1.688,1.281 2.302,1.479 0.615,0.198 10 false 9 1.698,0.813 2.313,1.01 0.615,0.198 10 false 3 5.656,0.906 6.271,1.104 0.615,0.198 10 false CANH 5.667,1.365 6.281,1.563 0.615,0.198 10 false CANL 5.427,1.26 6.042,1.458 0.615,0.198 10 false 1 5.438,0.781 6.052,0.979 0.615,0.198 10 false 4 5.646,2.938 6.26,3.135 0.615,0.198 10 false CB+ 5.667,3.51 6.281,3.708 0.615,0.198 10 false CGND 5.417,3.396 6.031,3.594 0.615,0.198 10 false 5 5.427,2.802 6.042,3 0.615,0.198 10 false 6 5.198,3.885 5.813,4.083 0.615,0.198 10 false R15 5.198,4.042 7,4.458 1.802,0.417 10 false Television Camera Assembly 0.292,3.75 0.906,3.948 0.615,0.198 10 false G2 0.292,3.917 2,4.302 1.708,0.385 10 false Radio and Display Receiver Assembly 1.198,3.521 1.813,3.719 0.615,0.198 10 false CGND 1.313,2.927 1.927,3.125 0.615,0.198 10 false CA+ 1.698,2.813 2.313,3.01 0.615,0.198 10 false 30 1.729,3.354 2.344,3.552 0.615,0.198 10 false 27

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (TELEVISION CAMERA ASSEMBLY BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C346954C46
1.5,0.146 1.906,0.354 0.406,0.208 1.344,1.938 1.51,1.938 1.51,1.938 1.51,1.427 true 1.365,0.469 1.51,0.469 1.51,0.469 1.51,1.083 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.583,0.177 1.896,0.333 0.313,0.156 10 false R15 0.938,1.885 1.427,2.052 0.49,0.167 10 false CANH 0.958,0.427 1.448,0.594 0.49,0.167 10 false CANL
*a Front view of wire harness connector
(to Television Camera Assembly)


Disconnect the television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R15-4 (CANH) - R15-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C346954C47
1.5,0.146 1.906,0.354 0.406,0.208 1.563,1.927 1.729,1.927 1.729,1.927 1.729,1.417 true 2.115,1.927 1.906,1.927 1.906,1.927 1.906,1.417 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.594,0.177 1.906,0.333 0.313,0.156 10 false R15 1.167,1.844 1.656,2.01 0.49,0.167 10 false CGND 2.156,1.865 2.646,2.031 0.49,0.167 10 false CB+
*a Front view of wire harness connector
(to Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R15-5 (CGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R15-6 (CB+) - Body ground Ignition switch ON 5.5 to 7.05 V
Ignition switch off Below 1 V



Result:
Result Proceed to
OK A
NG (w/ Panoramic View Monitor System) B
NG (w/ Parking Assist Monitor System) C



A

B

3.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - PARKING ASSIST ECU)

C

4.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - PARKING ASSIST ECU)
a.

Disconnect the N24 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R15-6 (CB+) - N24-33 (CB+) Always Below 1 Ω
R15-5 (CGND) - N24-32 (CGND) Always Below 1 Ω
R15-6 (CB+) or N24-33 (CB+) - Body ground Always 10 kΩ or higher
R15-5 (CGND) or N24-32 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (TELEVISION CAMERA ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the G2 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R15-6 (CB+) - G2-30 (CA+) Always Below 1 Ω
R15-5 (CGND) - G2-27 (CGND) Always Below 1 Ω
R15-6 (CB+) or G2-30 (CA+) - Body ground Always 10 kΩ or higher
R15-5 (CGND) or G2-27 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR