Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model)
RM3620E _57 Power Source / Network _076016 NETWORKING _0371267 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Headlight ECU LH Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Headlight ECU LH Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "HL AutoLeveling/AFS/AHS" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "HL AutoLeveling/AFS/AHS" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "HL AutoLeveling/AFS/AHS" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Headlight ECU LH Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Headlight ECU sub-assembly LH branch wire or connector

·

Power source circuit of headlight ECU sub-assembly LH

·

Headlight ECU sub-assembly LH ground circuit

·

Headlight ECU sub-assembly LH



WIRING DIAGRAM

C348701E48
0.229,1.958 2.563,2.271 2.333,0.313 10 false No. 7 CAN Junction Connector 0.229,1.76 0.625,1.969 0.396,0.208 10 false N52 1.719,1.469 2.115,1.677 0.396,0.208 10 false 11 1.719,0.885 2.115,1.094 0.396,0.208 10 false 5 5.323,0.865 5.719,1.073 0.396,0.208 10 false 24 5.323,1.427 5.719,1.635 0.396,0.208 10 false 23 5.688,1 6.083,1.208 0.396,0.208 10 false CANH 5.688,1.583 6.083,1.792 0.396,0.208 10 false CANL 5.323,2.354 5.719,2.563 0.396,0.208 10 false 13 5.688,2.49 6.083,2.698 0.396,0.208 10 false ECUB 5.385,3.177 5.781,3.385 0.396,0.208 10 false 4 5.677,3.313 6.073,3.521 0.396,0.208 10 false IG 5.344,4 5.74,4.208 0.396,0.208 10 false 12 5.677,4.135 6.073,4.344 0.396,0.208 10 false GND 5.031,4.792 5.427,5 0.396,0.208 10 false A11 5.031,4.938 7.104,5.74 2.073,0.802 10 false Headlight ECU Sub-assembly LH 3.896,3.156 5.125,3.417 1.229,0.26 10 false ECU-IG1 NO.3 1.844,2.448 3.531,2.917 1.688,0.469 10 false from H-LP LH Relay 1.792,3.271 3.281,3.615 1.49,0.344 10 false from IG1 NO.1 Relay

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (HEADLIGHT ECU SUB-ASSEMBLY LH BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C405881C04
1.479,0.448 1.917,0.719 0.438,0.271 2.406,2.802 2.573,2.802 2.573,2.802 2.573,1.969 true 2.521,3 2.688,3 2.688,3 2.688,2 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.573,0.5 1.927,0.729 0.354,0.229 10 false A11 2.052,2.917 2.5,3.167 0.448,0.25 10 false CANH 1.958,2.729 2.406,2.979 0.448,0.25 10 false CANL
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)


Disconnect the headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A11-24 (CANH) - A11-23 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C405881C05
1.479,0.448 1.917,0.719 0.438,0.271 0.677,2.615 0.844,2.615 0.844,2.615 0.844,1.958 true 1.823,1.792 1.823,0.938 1.823,0.938 1.99,0.938 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.583,0.521 1.938,0.75 0.354,0.229 10 false A11 0.323,2.542 0.771,2.792 0.448,0.25 10 false GND 2.042,0.865 2.49,1.115 0.448,0.25 10 false IG
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A11-12 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A11-4 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C405881C06
1.479,0.448 1.917,0.719 0.438,0.271 1.01,2.615 1.177,2.615 1.177,2.615 1.177,1.958 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.583,0.5 1.938,0.729 0.354,0.229 10 false A11 0.563,2.552 1.01,2.802 0.448,0.25 10 false ECUB
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A11-13 (ECUB) - Body ground For approximately 15 seconds after the ignition switch is turned to ON or off 11 to 14 V
Approximately 15 seconds elapsed after turning the ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE HEADLIGHT ECU SUB-ASSEMBLY LH

NG